Braun 5793 Mode D'emploi page 14

Accessories
Braun recommends changing your shaver's
Foil & Cutter cassette every 18 months to maintain
your shaver's maximum performance.
Available at your dealer or Braun Service Centres:
• Foil & Cutter cassette: 92S/92M
• Cleaning Cartridge: CCR
• Braun Shaver cleaner spray
Trouble-Shooting
Problem:
Shaver
Shaver does not start when
pressing the on / off button.
Charging does not start
when connected to power
socket or put in the Clean
& Charge Station.
Shaver does not charge
completely and keeps
blinking.
Unpleasant smell from the
shaver head.
Battery performance
dropped significantly.
Shaving performance
dropped significantly.
Shaver head is damp.
Clean & Charge Station
Cleaning does not start
when pressing the start
button.
Increased consumption of
cleaning fluid.
14
Possible reason:
1. The shaver can only be operated
cordless.
2. Travel lock is activated.
1. Sometimes charging starts
delayed (e.g. after long storage).
2. Ambient temperature is out of
valid range.
3. Power supply is not plugged into
the shaver properly.
4. Shaver is not placed properly in
the Clean & Charge Station.
Ambient temperature is out of valid
range.
1. Shaver head is cleaned with
water.
2. Cleaning cartridge is in use for
more than 8 weeks.
1. Foil and cutter are worn which
requires more power for each
shave.
2. Shaver head is regularly cleaned
with water but not lubricated.
1. Foil and cutter are worn.
2. Shaving system is clogged.
1. Drying time after automatic
cleaning was too short.
2. Drain of the Clean & Charge
station is clogged.
1. Shaver is not placed properly in
the Clean & Charge Station.
2. Cleaning cartridge does not
contain sufficient cleaning fluid
(display blinks red).
3. Appliance is in stand-by mode.
Drain of the Clean & Charge station
is clogged.
Environmental notice
Product contains batteries and / or recyclable
electric waste. For environment protection,
do not dispose of in household waste, but for
recycling take to electric waste collection
points provided in your country.
The cleaning cartridge can be disposed of with
regular household waste.
Subject to change without notice.
Remedy:
1. Unplug the shaver.
2. Press the on / off button for 5 seconds to
unlock the shaver.
1. Wait a few minutes. Charging will start
automatically.
2. Recommended ambient temperature for
charging is 5 °C to 35 °C.
3. Power supply needs to snap in.
4. Contacts of the shaver need to align with
contacts in the Clean & Charge Station.
Recommended ambient temperature for
charging is 5 °C to 35 °C.
1. When cleaning the shaver head with water
only use hot water and from time to time
some liquid soap (without abrasive
substances). Remove Foil & Cutter
cassette to let it dry.
2. Change cleaning cartridge at least every
8 weeks.
1. Renew Foil & Cutter cassette.
2. If the shaver is regularly cleaned with
water, apply a drop of light machine oil on
top of the foil once a week for lubrication.
1. Renew Foil & Cutter cassette.
2. Soak the Foil & Cutter cassette into hot
water with a drop of dish liquid. Afterwards
rinse it properly and tap it out. Once dry
apply a drop of light machine oil on the foil.
1. Wait until the drying process has been
completed.
2. Clean the drain with a wooden toothpick.
1. Insert shaver into the Clean & Charge
Station and push it to the rear side of the
station (contacts of the shaver need to
align with contacts in the station).
2. Insert new cleaning cartridge. Press the
start button again.
3. Press the start button again.
– Clean the drain with a wooden toothpick.
– Regularly wipe the tub clean.