Stiga SRC 550 RG Mode D'emploi page 16

HOW TO ASSEMBLE THE HANDLEBAR SUPPORT AND HANDLEBAR (Fig. 4)
assemble the handlebar support (1) on the
EN
tiller using the four screws (2) which are already placed on the plate, washers (3) and nuts (4) . Assemble the wire holder (5) as shown in the pict.
To assemble the handle (6) to the handlebar support (1) perform the following steps: pass the screw (7) in the top hole into the wire holder (8) in which
the wires have already been placed, then secure it with the nut (9). Use the screws for the lower slot (10) into the knobs (11) and washers (12). All the
mentioned pieces for mounting the handlebar , with the exception of the wire holder ( 8 ) ,can be found into the loose parts bag inside the box packaging.
To fix the handle ( 6) to the corresponding support (14) , you need to lower the lever (13) .
CONTROL CABLES ASSEMBLY (Fig. 5 - Fig. 6):
The two cables are already installed on the unit and must be connected to the
corresponding levers.
FORWARD (Fig. 5) Insert the wire (1) with the terminal T-slot (2) of the lever (3) pre-mounted on the handlebar. Place the cylindrical terminal (4) into
the seat of the lever (3) and give a firm tug to lock it. Then pinch the wire adjuster (5) into the seat (A)of the lever, by doing downward pressure.
REVERSE (Fig. 6): Insert the wire (1) marked with R label and the cylindrical terminal into the slot (2) of the lever (3) pre-assembled on the handlebar.
Place the cylindrical terminal (4) into the central seat (A) of the lever (3) and give a firm tug to lock it. Then insert the log thread (5) into place (B) of the
lever.
THROTTLE ASSEMBLY (Fig. 7)
The throttle wire is already mounted both on the engine inside the throttle device (1). Such a device is
fastened in the hole (A) of the handlebar with the screw (2) and locked with the nut (3).
HOW TO ASSEMBLE THE TREE SAVER DISKS (Fig. 7A)
Remove from the packing box the two tree saver disks (1). Insert the pin (A)
in the rotavator ( 2 ) up to make the holes (B) and (C) to match each other . Secure the whole with screw (3) and nut (4). Repeat the same operation
for the other disk.
HOW TO ASSEMBLE THE TUBE COVER FOR THE HANDLEBAR SUPPORT (Fig. 8)
Remove the cover ( 1) from the packing
box , catch it to the support tube handlebar (2) extending the flaps (A) and (B) , making sure the seats (C) to match with the knobs ( 3). Complete the
fastening by passing the screw (4 ) into the holes of the flaps (A) and (B) , and tighten using the nut ( 5 ) .
HOW TO ASSEMBLE THE HANDLEBAR COVER (Fig. 8 A)
Take the cover from the packing box (1). Place it making the seats to
fit each other (A) on the lower part of the handlebar ( 2 ) . Turn the cover as shown in the picture , making sure it matches with the lever ( 3). The cover
is properly installed when the hook (C) of the cover (1) is tightened to the pin (D) of the handlebar (2) .
CONTROL ADJUSTMENT : (Fig. 9)
Attention! The rotavator has to start working only after having operated on the control levers. Such
operation can be performed by acting on the handlebar cables (1 Forward speed) 2 (Reverse speed) register. Furthermore the lever controlling the
digging speed (3) should start the rotavator only after having performed half its way. When the lever (3) and the lever (4) are held toghether, i.e. on
working operation , the belt stretcher load-spring for forward speed ( 5e 6 ) should be extended for about 8-10 mm. If the handlebar register is not
enough to obtain any conditions , please go on another adjustment.
FORWARD: screw or unscrew the adjuster (7) or (8) on the wire (1).
16