McCulloch M3816 Manuel D'instructions page 9

All manuals and user guides at all-guides.com
Oil Cap
FUELING ENGINE
WARNING
: Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality 2-cycle air-cooled
engine oil designed to be mixed at a ratio of
40:1. A 40:1 ratio is obtained by mixing 0,125
liter of oil with 5 liters of unleaded gasoline. DO
NOT USE automotive or boat oil. These oils
will cause engine damage. When mixing fuel
follow the instructions printed on the container.
Always read and follow the safety rules relating
to fuel before fueling your unit.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads
to separation and formation of acids during
storage. Acidic gas can damage the fuel sys-
tem of an engine while in storage. To avoid
engine problems, empty the fuel system be-
fore storage for 30 days or longer. Drain the
gas tank, start the engine and let it run until
the fuel lines and carburetor are empty. Use
fresh fuel next season. Never use engine or
carburetor cleaner products in the fuel tank
or permanent damage may occur.
CHAIN BRAKE
Ensure chain brake is disengaged by pulling
the front hand guard back toward the front han-
dle as far as possible. The chain brake must
be disengaged before cutting with the saw.
WARNING
: The chain must not
move when the engine runs at idle speed. If
the chain moves at idle speed refer to CAR-
BURETOR ADJUSTMENT within this
manual. Avoid contact with the muffler. A hot
muffler can cause serious burns.
To stop the engine, move the ON/STOP
switch to the STOP position.
To start the engine, hold the saw firmly on
the ground as illustrated below. Make sure
the chain is free to turn without contacting
any object.
Use only 40 --- 45 cm of rope per pull.
Hold saw firmly while pulling starter rope.
IMPORTANT POINTS TO REMEMBER
Fuel mix cap
When pulling the starter rope, do not use the full
extent of the rope as this can cause the rope to
break. Do not let starter rope snap back. Hold
the handle and let the rope rewind slowly.
For cold weather starting, start the unit at full
choke; allow the engine to warm up before
squeezing the throttle trigger.
NOTE
fast idle lever at the FULL CHOKE position.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
NOTE
choke/fast idle lever is pulled out to the full
extent, the correct throttle setting for starting
is set automatically.
1. Move ON/STOP switch to the ON posi-
2. Slowly press primer bulb 6 times.
3. Pull out choke/fast idle to the full extent
4. Pull the starter rope sharply 5 times with
NOTE
to start before the 5th pull, stop pulling and
immediately proceed to the next step.
5. Push the choke/fast idle lever in to the
6. Pull the starter rope sharply with your
7. Allow the engine to run for approximately
STARTING A WARM ENGINE
1. Move ON/STOP switch to the ON position.
2. Slowly press the primer bulb 6 times.
3. Pull the choke/fast idle lever out to the
4. Pull the starter rope sharply with your
5. Squeeze and release throttle trigger to
DIFFICULT STARTING (or starting a
flooded engine)
The engine may be flooded with too much
fuel if it has not started after 10 pulls.
Flooded engines can be cleared of excess
fuel by pushing the choke/fast idle lever in
9
: Do not cut material with the choke/
: In the following steps, when the
ON/STOP SWITCH
(SIDE VIEW)
ON
STOP
tion.
(to the FULL CHOKE position).
your right hand. Then, proceed to the
next step.
: If the engine sounds as if it is trying
HALF CHOKE position.
CHOKE/FAST IDLE LEVER
(SIDE VIEW)
Choke/
fast idle lever
OFF HALF
right hand until the engine starts.
30 seconds. Then, squeeze and release
throttle trigger to allow engine to return to
idle speed.
HALF CHOKE position.
right hand until the engine starts.
allow engine to return to idle speed.
FULL