Publicité
Les langues disponibles
Les langues disponibles
Always use a clamp or a fixture designed
o)
to properly support round material such as
rods or tubing. Rods have a tendency to roll
while being cut, causing the blade to "bite" and
pull the work with your hand into the blade.
p)
Let the blade reach full speed before con-
tacting the workpiece. This will reduce the risk
of the workpiece being thrown.
q)
If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed materi-
al. Continued sawing with a jammed workpiece
could cause loss of control or damage to the mi-
tre saw.
r)
After finishing the cut, release the switch,
hold the saw head down and wait for the
blade to stop before removing the cut-off
piece. Reaching with your hand near the coast-
ing blade is dangerous.
Hold the handle firmly when making an in-
s)
complete cut or when releasing the switch
before the saw head is completely in the
down position. The braking action of the saw
may cause the saw head to be suddenly pulled
downward, causing a risk of injury.
Safety Instructions for the handling of saw
blades
1.
Do not use damaged or deformed saw blades.
2.
Do not use any insertion tools with cracks. Sort
out cracked insertion tools. Repairs are not per-
mitted.
3.
Do not use saw blades made of high speed steel.
4.
Check the condition of the saw blades before us-
ing the trim, chop and mitre saw.
5.
Make sure that a suitable saw blade for the ma-
terial to be cut is selected.
6.
Only use saw blades recommended by the man-
ufacturer. Saw blades designed to cut wood and
similar materials must comply with EN 847-1.
7.
Do not use saw blades made of high-speed alloy
steel (HSS steel).
8.
Only use saw blades for which the maximum
permissible speed is not lower than the maxi-
mum spindle speed of the trim, chop and mitre
saw, and which are suitable for the material to
be cut.
9.
Observe the saw blade direction of rotation.
10. Only insertion the saw blade if you have mas-
tered their use.
11. Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
12. Clean grease, oil and water off of the clamping
surfaces.
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
13. Do not use any loose reducing rings or bushes
for the reducing of holes on saw blades.
14. Make sure that fixed reducer rings for securing
the insertion tool have the same diameter and
have at least 1/3 of the cutting diameter.
15. Make sure that fixed reducer rings are parallel
to each other.
16. Handle insertion tool with caution. They are ide-
ally stored in the originally package or special
containers. Wear protective gloves in order to im-
prove grip and to further reduce the risk of injury.
17. Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
18. Prior to use, ensure that the saw blade meets
the technical requirements of this trim, chop and
mitre saw, and is properly fastened.
19. Only use the supplied saw blade for cutting
wood, never for the processing of metals.
20. Only use saw blade diameters in accordance
with the markings on the saw.
21. Use additional workpiece supports, if required
for workpiece stability.
22. Workpiece support extensions must always be
secured and used during work.
23. Replace table inserts when worn!
24. Avoid overheating of the saw teeth.
25. When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose.
Replace damaged or worn saw blades immedi-
ately.
When the saw blade overheats, stop the ma-
chine. Allow the saw blade to cool down before
using the machine again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unpro-
tected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
GB | 27
Publicité
