LUND 67572 Mode D'emploi page 11

EN
insert. The insert is mounted in the bowl by means of a latch hidden under the movable housing. When carrying the bowl, always cover
the latch with a housing. This will prevent accidental separation of the bowl from the insert. The latch may be released only when the bowl
is placed on the ground. Put the bowl with hot food only on the grand that withstands high temperature, or use protective stands. While
preparing the inside of the chamber and dishes themselves, you may touch them only with the use of tools made of such materials that
will withstand the temperature produced by the product. It is forbidden to use for this purpose your bare hands. Do not use sharp, metal
objects that may damage unstickable surface of the bowl and insert. If any food waste remains during or after preparation of a dish inside
the bowl or insert, it should be removed before preparing next dish. Food waste may be burnt, thus generating a smoke, unpleasant odour,
and also aff ect the taste of a meal prepared. They may also cause a fi re. To remove it, use tools made of wood or plastics that withstand
a temperature produced by the product. Do not use sharp tools made of metal. Such tools may damage a surface of the bowl and insert.
PRODUCT HANDLING
Control panel
67572
The product is equipped with a touch control panel with an LED display and a knob/button.
When the product is connected to the power supply, a sound signal will be heard and all symbols will be briefl y highlighted, fol-
lowed by an indication on the display: "---". The product is in standby mode.
Touching the on/off switch or any button, or rotating or pressing the knob will activate the product's setting mode.
The display will show the default setting of temperature and time in minutes. To change the setting, use the knob, turn clockwise
to increase the setting, turn counter clockwise to decrease the setting. Each touch of the button is indicated by a sound signal and
a change in the display status.
Touching the button with the clock symbol allows you to change the time setting.
Touching the button with the thermometer symbol allows you to change the temperature setting.
By touching the "M" button, you can select one of the predefi ned operating modes by turning the knob. Each mode is a combina-
tion of time and temperature settings shown on the display. The operating modes can be changed in the following cycle: French
fries – ribs – shrimps – cake – poultry – meat – fi sh.
Caution! When programming the settings, the product automatically returns to standby mode approximately one minute after the
last touch of any button or rotation of the knob.
After setting the time and temperature in less than one minute, lightly press the knob. This will cause the device to begin operating.
This will be indicated by a fl ashing fan symbol. The fan symbol highlighted red indicates the operation of the product heater. The
fan symbol highlighted blue indicates that the fan is working.
The product can be turned off at any time by touching the on/off switch. After switching off , the fan can still work for some time,
accelerating the heater cooling process. Do not disconnect the product from the power supply during this time. When the cooling
of the heater is fi nished, the product will automatically switch to standby mode. The device power supply cord plug must then be
disconnected from the socket.
67573
The product's control panel includes two knobs and light indicator.
The upper knob is used for temperature setting.
The lower knob is used for time setting.
Lighting up of indicator indicates the heater operation. The product has been fi tted with inner temperature sensor. While operating
the indicator may switch in and off automatically.
The product may be disconnected at any moment by switching the time setting knob to "0".
67574
The product has been fi tted with touch control panel with light display.
After the product is plugged to mains, an acoustic signal shall be emitted and the display will show: „---". Also the switch button
shall be backlit. The product is in standby mode.
Touching the button will activate the product setting mode.
The display will alternately show a default temperature and time setting in minutes.
Using buttons marked with a watch symbol you may change time setting.
Using buttons marked with a thermometer symbol you may change temperature setting.
"+" marked button increases and "-" marked button decreases the setting value.
Each touch of a button will be signalled by an acoustic signal and change of setting shown on a display.
"M" marked button allows selecting one of the predefi ned operating modes. Each mode is a combination of time and temperature
settings, shown alternately on a display.
The selection of a mode is signalled by an acoustic signal and backlighting of a symbol of selected mode on a display. In each
mode, time and temperature settings may be changed. However, they will not be saved as new settings of a given mode.
Operating modes can be changed in the following cycle: French fries – ribs – shrimps – cake – poultry – meat – fi sh.
O R I G I N A L I N S T R U C T I O N S
11