Kärcher HD 5/11 C Mode D'emploi page 17

Finishing operation
1. Close the water inlet.
2. Open the high-pressure gun.
3. Set the power switch to "I/ON" and allow the device
to run for 5-10 seconds.
4. Close the high-pressure gun.
5. Set the power switch to "0/OFF".
6. Pull the mains plug out of the socket only when your
hands are dry.
7. Remove the water inlet.
8. Open the high-pressure gun until the device is com-
pletely depressurised.
9. Push the safety latch forwards.
The high-pressure gun is secured.
Transport
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transport
and storage.
ATTENTION
Improper transportation
Risk of damage
Protect the trigger of the high-pressure gun from dam-
age.
Transporting the device in a vehicle: Secure the de-
vice in accordance with the respectively applicable
guidelines to prevent it from slipping or overturning.
Transporting the device over longer distances: Pull
the device behind you via the push handle.
Transporting the device over stairs: Pull the device
step by step. The skids protect the casing from dam-
age.
Carrying the device: Carry the device by the handles
only.
Transport retainer for surface cleaner
1. Plug the connection union of the surface cleaner on-
to the transport holder of the high-pressure cleaner.
2. Screw on the union nut by approximately 1 turn.
Crane transport
DANGER
Improper crane transport
Risk of injury from a falling device or falling objects
Observe the local regulations for accident prevention
and the safety instructions.
The device may only be transported with a crane by per-
sons instructed in the operation of the crane.
Check the lifting gear for damage before each crane
transport.
Check the handle for damage before each crane trans-
port.
Lift the device only by the handle.
Do not use an slinging chains.
Secure the lifting gear against unintentional unhooking
of the load.
Remove the spray lance with high-pressure gun, noz-
zles, surface cleaner and other loose objects before
transporting by crane.
Do not transport any objects on the device during the
lifting operation.
Do not stand under the suspended load.
Ensure that no persons are in the hazard zones of the
crane.
Do not leave the device handing unattended on the
crane.
1. Attach the lifting gear to the handle on the device.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transport
and storage.
Store the device indoors only.
Storing the device
1. Fit the spray lance with high-pressure gun into the
nozzle holder and latch into position in the spray
lance holder.
2. Roll up the mains cable and hang it over the cable
holders.
3. Fasten the plug with the clip provided.
For devices with a hose reel:
4. Wind the high-pressure hose onto the hose reel and
fold over the crank handle.
For devices without a hose reel:
5. Storing the high-pressure hose:
a Wind up the high-pressure hose.
b Hang the high-pressure hose over the hose stor-
age compartment.
c Secure the high-pressure hose with the rubber
band.
6. Press the push handle lock and slide in the push
handle.
ATTENTION
Frost
Destruction of the device through freezing water
Drain all water from the device.
Store the device in a frost-free location.
If frost-free storage is not possible:
1. Drain the water.
2. Pump commonly available anti-freeze through the
device.
Note
Use commonly available, Glycol-based vehicle anti-
freeze. Observe the handling instructions of the anti-
freeze manufacturer.
3. Allow the device for run for a maximum of 1 minute
until the pump and lines are empty.
Care and service
DANGER
Inadvertently starting up device
Risk of injury, electric shock
Switch off the device immediately and unplug the mains
plug before performing work.
English
Storage
Frost protection
17