Gardena 14800 Mode D'emploi page 12

1. Pull the protective cover (S)
(B)
2. Put the battery into the battery holder
3. Push the starting lockout
The washer starts and the battery charge status indication
displayed for 5 seconds.
4. Release the starting lockout
The washer continues to run without having to push the starting lock-
out.
To stop:
(16)
1. Release the start lever .
The washer stops.
2. Close the water supply (e. g. water tap).
3. Pull the start lever (16) to depressurize the system.
4. Disconnect the suction hose from the washer.
(A)
5. Push the locking button
holder (D) .
Use in suction mode:
1. Push the starting lockout
start lever (16) .
2. Switch off the Soft-Clean mode during priming
(LED (Le) is not illuminated).
3. Prime at a low height (approx. 0 to 1 m).
4. Wait until water is pumped and full pressure is reached.
5. Then move to your working position.
It can take up to 30 seconds (at higher suction heights) until the
water is delivered in suction mode. The maximum suction height
is 2 m.
4. MAINTENANCE
DANGER! Risk of injury!
Eye injury and personal injury caused by the water jet.
v Remove the battery before you maintain the product.
To clean the washer [ Fig. M1 ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
(17)
1. Clean the airflow slots
2. Clean all movable parts after each operation. Especially remove any
dirt from the connections.
3. Unscrew the connection (7)
size 17).
4. Remove the device filter (18)
under running water.
5. Remove the spray lance (1)
water.
6. Remove the suction filter
(7)
7. Screw the connection hand-tight into the washer.
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the battery
charger always are clean and dry before you connect the battery charger.
Do not use running water.
v Battery charger: Clean the contacts and the plastic parts with a soft
and dry cloth.
v Battery: Occasionally clean the ventilation slots and the terminals on
the battery using a soft brush that is clean and dry.
5. STORAGE
To put into storage:
The product must be stored away from children.
12
14800-20.960.02.indd 12
over the battery (B) .
(D)
until it audibly engages.
(L) on the left side and pull the start lever
(P)
(L)
again.
(B)
and remove the battery from the battery
(L) on the left side and pull the
with a soft brush (do not use a screwdriver).
(if necessary using a spanner with spanner
from the connection (7) and clean the filter
and rinse the spray lance (1) with clear
(12) and clean the suction filter (12) .
1. Remove the battery.
2. Charge the battery.
3. Clean the washer, the battery and the battery charger
(16) .
(see 4. MAINTENANCE).
is
4. Store the washer, the battery and the battery charger in a dry,
enclosed and frost-free place.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
Disposal of the battery:
The GARDENA battery contains lithium-ion cells that should not
be disposed of with normal household waste at the end of its life.
Li-ion
IMPORTANT!
v Dispose of the batteries through or via your municipal recycling
collection centre.
1. Discharge the lithium-ion cells completely (contact the GARDENA
Service).
2. Protect the contacts on the lithium-ion cells against short circuits.
3. Dispose of the lithium-ion cells properly.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Eye injury and personal injury caused by high pressure
water jet.
v Remove the battery before you troubleshoot the product.
Problem
Washer conveys no
or almost no water
Pressure drop during
operation
Water is badly sucked
in from the water tank
Washer does not stop
Washer does not start
or stops.
(L1)
LED is flashing green
[ Fig. O4 ]
Washer does not start
or stops.
(Wp)
Error-LED is illuminated
red [ Fig. O4 ]
Possible Cause Remedy
Water container is empty. v Fill the water container.
Air is in the system. v Remove the lance and push
the start lever for about
30 seconds until water is
visibly pumped.
Reassemble the lance.
Air is in the system. v Ventilate the system at low
altitude. Then move to the
working position.
Device filter v Clean the device filter and
(see 4. MAINTENANCE), suction suction filter. Clean the
filter or nozzle is clogged. nozzles e. g. with a needle.
Device filter or suction filter v Clean the device filter
is dirty. and suction filter
(see 4. MAINTENANCE).
Battery charge level is too low. v Charge the battery.
Suction height too high. v Reduce the suction height.
Air is in the system. v Remove the lance and push
the start lever for about
30 seconds until water is
visibly pumped.
Reassemble the lance.
Device filter or suction filter v Clean the device filter
is dirty. and suction filter
(see 4. MAINTENANCE).
Start lever is stuck. v Remove the battery and
loosen the start lever.
Battery is empty. v Charge the battery.
Battery temperature is outside v Wait until the battery
the permissible temperature tem perature is between
range. 0 °C – + 45 °C again.
Washer is overheated v Let the washer cool down in
(e. g. by direct sunlight). a cool, shady place.
06.11.20 11:44