Gardena 14800 Mode D'emploi page 11

2. Pull the ring (3) of the quick coupling backwards, push the desired
attachment (4) on the spray lance
The coupling is fully engaged when the ring is again at the front
(the silver retaining spring and the silver balls are no longer visible).
(4)
3. Turn the attachment for the desired spraying angle.
The two unused nozzles (4) can be placed on the holders
4. Connect the suction hose
To assemble the detergent tank (Premium Set) [ Fig. A4 ]:
For cleaning with detergent, the detergent tank can be attached to the
(1)
front of the short lance .
1. Fill the detergent container
2. Pull the ring (3) of the quick coupling backwards, place the detergent
tank (8) on the short spray lance
The coupling is fully engaged when the ring is again at the front
(the silver retaining spring and the silver balls are no longer visible).
3. Dose the amount of detergent with the dosing wheel
To provide the water supply:
You can enable the water supply via the water bag (Premium Set),
via a water tank (pond, rain barrel, etc.) or via a water tap.
Water supply via the water bag (Premium Set) [ Fig. A5 ]:
1. Carry the full water bag by the handle and place it on a firm surface
when in use.
2. Unscrew the cap (10) .
3. Fill the water bag (11) with clear tap water.
4. Remove the suction filter
5. Move the float ball (13) upwards.
6. Immerse the suction hose
7. Attach the hose (6) to the water bag
The hose (6) must be completely immersed in the water.
Water supply via a water tank [ Fig. A6 ]:
1. Immerse the suction filter
The suction filter (12) must be completely immersed in the water.
(13)
2. Move the float ball in such a way that the suction filter
touch the ground.
This prevents the suction filter from clogging.
3. Attach the hose (6) to the water tank with the plastic clip
Note:
When water is supplied via a water tank, the suction filter
used.
Only clear fresh water may be used.
Water supply via a water tap [ Fig. A7 ]:
The washer is leak-proof up to 1.0 MPa (10.0 bar) water inlet pressure.
For an optimal cleaning result 0.6 MPa (6.0 bar) water inlet pressure must
not be exceeded.
1. Connect the enclosed suction hose
2. Open the water tap.
Alternatively, a garden hose can also be connected.
CAUTION!
v Close the water tap and disconnect the washer from the tap
after cleaning.
3. OPERATION
DANGER! Risk of injury!
Eye injury and personal injury caused by the water jet.
v Remove the battery before you adjust or transport the product.
To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
v Note the mains voltage! The voltage of the power source must
match the voltage specified on the rating plate of the charger.
14800-20.960.02.indd 11
(1) and release the ring (3) again.
(5) .
(6) (7)
to the connection .
(8)
with detergent.
(1) and release the ring (3) again.
(9)
.
(12)
.
(6) (11)
in the water bag .
(11) .with the plastic clip (14)
(12) (6)
of the suction hose in the water tank.
(12)
does not
(14) .
(12) must be
(6) (15)
to a water tap .
For the GARDENA Battery Cleaner Art. 14800-55 there is no battery
and no charger in the scope of delivery.
Thanks to the intelligent charging process, the charge condition of the
battery is automatically detected and then charged up with the optimal
charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully
charged when it is stored in the charger.
1. Push the locking button
holder (D) .
2. Remove the battery
3. Connect the battery charger
4. Slide the battery charger
When the battery charge indicator
the battery is being charged.
When the battery charge indicator
permanently green the battery is completely charged
(Charging time, see 7. TECHNICAL DATA).
5. Examine the charge status regularly while you charge.
6. When the battery
battery (B) from the charger
Meaning of the indication elements:
Indication on the charger [ Fig. O3 ]:
Flashing of the battery The charging procedure is indicated by flashing of the battery charge
(Lc)
charge Indicator indicator
Note: The charging procedure is only possible when the battery
temperature is within the allowable charging temperature range,
see 7. TECHNICAL DATA.
Continuous lighting Continuous lighting of the battery charge indicator
of the battery the battery is fully charged or that the temperature of the battery is
(Lc)
charge indicator not within the allowable charging temperature range and can therefore
. not be charged.
When the battery is not inserted, continuous lighting of the battery
charge indicator
socket outlet and that the battery charger is ready for operation.
Battery charge status indication
After starting the product, the battery charge status indication
is displayed for 5 seconds.
Battery charge status
67 – 100 % charged
34 – 66 % charged
11 – 33 % charged
0 – 10 % charged
If the LED (L1) flashes green, the battery must be charged.
If the error LED (Wp) is illuminated or flashing, see 6. TROUBLESHOOTING.
Control panel [ Fig. O5 ]:
Soft Clean Mode:
The soft-clean mode reduces the spray pressure for cleaning sensitive
surfaces. It also extends the battery life.
There are 3 different operating modes:
Soft Clean-Mode high (24 bar)
Soft-Clean-Mode soft (14 bar)
Soft-Clean-Mode ultra soft (9 bar)
The specified pressure values may vary depending on the inlet
pressure.
v Push the Soft Clean button
the desired mode is displayed.
To start the washer [ Fig. O1 /O6 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example
do not attach the start lever to the handle.
To start:
The product is provided with a safety device (start lever with start-
ing lockout) to prevent the product from being turned on by acci-
dent.
The washer may only be used with a battery when the protective
cover (S) has been slid onto the battery.
(A) and remove the battery (B)
(B) from its protective cover (S) .
(C)
into a mains socket.
(C) onto the battery (B) .
(Lc) at the charger flashes green
(Lc) at the charger illuminates
(B)
is completely charged, you can disconnect the
(C) .
(Lc)
.
(Lc)
indicates that the mains plug is inserted in the
(P) on the product [ Fig. O4 / O6 ]:
Battery charge status indication
(L1) (L2) (L3)
, and illuminate green
(L1) and (L2) illuminate green
(L1)
illuminates green
(L1)
flashes green
(Le) does not illuminate
(Le) is flashing
(Le)
illuminates
(e) on the control panel repeatedly until
from the battery
(Lc) indicates that
(P)
11
06.11.20 11:44