Publicité
Les langues disponibles
Les langues disponibles
TECHNICAL DATA
Type
Production code
Voltage battery
Cycle rate
Staples:
Staple Strip
Width
Length
Diameter
Magazine capacity (number of staples)
Weight according EPTA-Procedure 01/2014 (2,0 Ah ... 12,0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
Noise information:
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Always wear ear protectors!
Vibration information: Total vibration values (vector sum in the three
axes) determined according to EN 60745.
Vibration emission value a
/ Uncertainty K
h
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN
60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications,
with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level
over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY WARNINGS CORDLESS STAPLER
Always assume that the tool contains staples. Careless handling
of the stapler can result in unexpected fi ring of staples and personal
injury.
Do not point the tool towards yourself or anyone nearby.
Unexpected triggering will discharge the staple causing an injury.
Do not actuate the tool unless the tool is placed fi rmly against
the workpiece. If the tool is not in contact with the workpiece, the
staple may be defl ected away from your target.
Disconnect the tool from the power source when the staple jams
in the tool. While removing a jammed staple, the stapler may be
accidentally activated if it is plugged in.
Use caution while removing a jammed staple. The mechanism
may be under compression and the staple may be forcefully
discharged while attempting to free a jammed condition.
Do not use this stapler for fastening electrical cables. It is not
designed for electric cable installation and may damage the insulation
of electric cables thereby causing electric shock or fi re hazards.
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the staple may contact hidden
wiring. Staple strips contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an electric
shock.
24
M18 FFUS
Fencing Stapler
4913 23 01 XXXXXX MJJJJ
18 V
600
20
10,3 mm
38 - 51 mm (1,5"-2")
3,7 mm (9 GA)
45
10,39...11,45 kg
-18...+50 °C
M18B...; M18HB...
M12-18...; M1418C6
79,1 dB(A) / 3 dB(A)
90,1 dB(A) / 3 dB(A)
2,3 m/s
/ 1,5m/s
2
2
Always wear eye protection with side shields. Everyday glasses
have only impact resistant lenses. They are not safety glasses.
Following this rule will reduce the risk of serious personal injury.
Eye protection provides protection against flying particles both
from the FRONT and SIDE should ALWAYS be worn by the
operator and others in the work area when loading, operating or
servicing this tool. Eye protection is required to guard against flying
staples and debris, which could cause severe eye injury.
Always remove the battery before adjusting the depth of drive wheel.
Do not pull back on the adjustment wheel, the wheel is designed to
be rotated.
Do not press the trigger while adjusting the depth of drive wheel.
Always select full sequential fi ring mode before adjusting the depth
of drive.
Do not point the tool towards yourself or anyone nearby when
adjusting the depth of drive.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Always be aware that misuse and improper handling of this tool can
cause injury to yourself and others.
The tool is designed for single-hand use. Do not hold the tool by the
front of the magazine. Do not put hands, head, or other parts of your
body near the bottom of the magazine where the staple exits the tool,
as serious personal injury could be caused.
Always ensure that the workpiece contact is fully positioned above the
workpiece. Positioning the workpiece contact only partially above the
workpiece could cause the staple to miss the workpiece completely
and result in serious personal injury.
Do not drive staple near edge of material. The workpiece may split
causing the staple to ricochet, injuring you or a coworker. Be aware
that the staple may follow the grain of the wood, causing it to protrude
ENGLISH
unexpectedly from the side of the work material or defl ect, possibly
causing injury.
Keep hands and body parts clear of immediate work area. Hold
workpiece with clamps when necessary to keep hands and body out
of potential harm. Be sure the workpiece is properly secured before
pressing the staple against the material. The workpiece contact may
cause the work material to shift unexpectedly. Keep face and body
parts away from back of the tool cap when working in restricted
areas. Sudden recoil can result in impact to the body, especially when
working into hard or dense material.
During normal use the tool will recoil immediately after driving a
staple. This is a normal function of the tool. Do not attempt to prevent
the recoil by holding the stapler against the work. Restriction to the
recoil can result in a second staple being driven from the stapler. Grip
the handle fi rmly, let the tool do the work and do not place second
hand on top of tool or near exhaust at any time. Failure to heed this
warning can result in serious personal injury.
Do not drive staples on top of other staples or with the tool at an
overly steep angle as this may cause defl ection of staples which could
cause injury.
Always check the work area for hidden wiring, gas lines, water lines,
etc., before using the product on such work area.
The driving depth of the staple may be adjusted beyond air pressure.
It is advisable to test the depth on a scrap workpiece to determine the
required depth for the application.
Only staples matching the description in the Technical Data can be
used with this tool. Using incorrect staples may lead to jamming or
other malfunctions.
Do not dispose of used battery packs in the household refuse or by
burning them. Milwaukee Distributors off er to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short circuit
risk).
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
Use only 18 V chargers for charging 18 V battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in fl uid or allow a fl uid to fl ow inside them. Corrosive or
conductive fl uids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The stapler is intended for driving staples into wood or similar soft
materials from a magazine containing a strip of suitable nails. The
staple strip which can be safely loaded into the magazine for the
product are described in the product specifi cation table in this manual.
Do not use any other type of staple or fi xing with the Stapler. The
Stapler should not be used for fi xing electric cables.
Do not use this product in any other way as stated for normal use.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Injury caused by vibration
Hold the product by designated handles and restrict working time
and exposure.
• Exposure to noise can cause hearing injury.
Wear ear protection and limit exposure.
• Injury due to fl ying debris
Wear eye protection, heavy long trousers, gloves and substancial
footwear at all times.
• Inhalation of toxic dusts.
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the batteries have to be fully charged, after
used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away from
moisture
Store the battery in a 30% - 50% charged condition
Every six months of storage, charge the battery as normal.
Battery protection for Li-Ion batteries
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will vibrate for about 5 seconds,
the fuel gauge will fl ash,and then the tool will turn OFF. To reset,
release the trigger.
Under extreme circumstances, the internal temperatur of the battery
could become to high. If this happens, the fuel gauge will fl ash and
the battery pack cool and then continue work.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
ENGLISH
25
Publicité
