Nolan N21 VISOR Sécurité Et Instructions D'utilisation page 8

N21 VISOR
intensity and/or incidence of sunlight.
- At night and/or in conditions of poor visibility, the VPS must be deactivated.
- Should sunglasses and/or photochromic lenses be used, the VPS must be deac-
tivated.
- Always check that the VPS is properly positioned according to the different weath-
er/environmental conditions and/or to the above mentioned usage recommenda-
tions.
- Use the special slider to activate/deactivate the VPS; do not deactivate the VPS
by handling it directly.
- Always make sure that the VPS is clean and that it is operating properly in order to
avoid scratches and/or anomalous wear on it every time it is activated.
- As for VPS and visor maintenance and cleaning operations, please refer to the
appropriate section in the helmet user's manual.
- The VPS scratch resistant/fog-resistant treatment highly reduces fogging. Howev-
er, protracted periods of adverse weather and/or environmental conditions might
cause fogging and/or formation of condensation on the VPS, which entails a re-
duction of visibility and/or sharpness of vision: in this case, deactivate the VPS.
- In case of rain, the direct contact of raindrops with the scratch resistant/fog-resist-
ant treated VPS quickly reduces sharpness of vision, thus causing scarce visibility:
in this case, deactivate the VPS.
- The special VPS fog-resistant treatment is usually sensitive to high temperatures
or heat sources. In this case, contaminations caused by contact with other ma-
terials might occur. These contaminations will cause marks and stains to come
out. In these cases (e.g. when the helmet is kept in the top case on hot days), it is
recommended that the VPS does not come into contact with other materials.
3 VPS DISASSEMBLY
To remove the sunscreen from the helmet, open the visor completely and lower the VPS
by pushing the slider completely upwards (Fig.7B).
Hold the left lateral part of the sun screen and pull it toward the outside of the helmet
(Fig.8). Repeat the same operation on the right side of the helmet.
4 VPS ASSEMBLY
To remove the sunscreen, open the visor completely and push the slider completely
upwards (Fig.7B).
Insert the sun screen left end into the left side guide until the grip pawl is hooked in shell
housing (Fig.8).Repeat the same operation on the right side of the helmet.
WARNING
- Push the left side slider completely downwards (Fig.7A) and upwards (Fig.7B) to
make sure that the VPS works properly. If necessary, repeat the above-mentioned
steps.
- If the VPS opening/closing mechanisms are damaged or not working properly,
please contact a Nolangroup authorized dealer.
- Do not use the helmet if the VPS has not been assembled properly.
- Since the VPS does not assure you the same protection as the one provided by
the visor, it has to be used only when the helmet visor is lowered.
14
INSTRUCTIONS FOR USE
VPS LOWER EDGE TRIM
The lower VPS sunscreen profile is moulded with a printed trim attached to the visor
with fastening elements.
1 VPS TRIM DISASSEMBLY
To release the trim from the lower edge of the sunscreen, first remove the sunscreen
from the helmet (see instructions above).
1.1 Pull the trim right end downwards to release the first fastening from the sunscreen
(Fig.9).
1.2 Continue releasing the other fastenings one by one, moving towards the other end
of the sunscreen (Fig.10).
1.3 Pull out the trim from the sunscreen left side flap (Fig.10).
1.4 Release the trim left end and completely remove it from the sunscreen (Fig.11).
2 VPS TRIM ASSEMBLY
2.1 Insert the left side flap of the sunscreen in its slot on the trim (Fig.12).
2.2 Press the trim left end against the sunscreen to attach it to the relevant fastening
element (Fig.10).
2.3 Continue attaching the other fastenings one by one, moving towards the other end
of the sunscreen (Fig.10).
2.4 Press the trim right end against the sunscreen to attach it to the relevant fastening
element (Fig.9).
2.5 Push the trim against the sunscreen aligning it with all the fastening device in
order to attach it evenly along the whole sunscreen lower edge; check that all the
fastening devices are correctly attached and that the trim and the visor fit together
tightly. Finally, fit the sunscreen on the helmet (see instructions above).
WARNING
- Never use the helmet without having correctly assembled the sunscreen trim
- Make sure the VPS operates correctly by moving the left side slider downwards
(Fig.7A) and upwards (Fig.7B) and check that the visor lower edge trim does not
come out of the sunscreen. If necessary, repeat the above-mentioned steps.
- In case of malfunctioning or damages, please contact an authorized Nolangroup
dealer.
REMOVABLE INNER COMFORT PADDING
1 INNER COMFORT PADDING DISASSEMBLY
To remove the inner comfort padding, lift the VPS and open the visor completely (see
instructions above).
1.1 Open the chin strap (see specific instructions).
1.2 Hold the left front part of the liner and pull it upwards in order to remove the liner
flap from the support fixed to the polystyrene inner shell (Fig.13). Then repeat the
same steps for the central front and right flap.
1.3 Remove the left and right sides of the comfort padding from the cavity between
N21 VISOR
15
INSTRUCTIONS FOR USE