Loewe WM Flex 26 S Instructions D'installation page 9

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12
Installation
The enclosed instructions show / refer to Æ xing to vertical brick or concrete walls.
The person installing the TV is responsible for assessing the load bearing capacity of the wall and the fastening
of the wall holder.
Because of the possible different wall building materials and the necessary fastening parts we have not included any fastening
parts. Buy suitable fastening parts for your wall from a dealer.
Consult a building expert if necessary.
Make sure that there are no cables / pipes near to where you drill the holes.
See the sketches on pages 16 to 19 (foldout installation sketch).
Fastening is done in this example with 4 wall plugs 8 x 65 mm (sketch 4, arrow A) and suitable countersunk screws 5 x 70 mm
(sketch 4, arrow B)
Attention, use screws with heads of a size and shape to Æ t in the recesses in the wall plate. The screw heads must not protrude
from the wall plate.
Installation instruction WM Flex 26 S
Preparing the WM Flex 26 S wall holder for installation
The wall holder with its individual parts comes in a kit.
You will Å nd the individual parts and dimensions in the function drawing on page 16, Å g. 1.
The drawings on pages 17 / 18 and 19 fold out.
Part 1: Wall plate with jointed arm
Part 2: Setting screw for tilting the TV set
Part 3: Fastening plate for TV set
Part 4: Fastening screws (4) for the TV set
Part 5: Insertion roller
Part 6: Threaded pin (two available)
Check that the scope of delivery is complete.
Fixing the wall plate with jointed arm "1"
Select the fastening location and check that there are no cables or pipes concealed in the wall beneath it.
Use the wall plate as a template for marking the drill holes.
Recommended procedure
Align the wall plate on the wall using a spirit level.
Mark the holes on the wall through the openings in the wall plate.
Drill the holes to suit your fastening materials.
In the example with 4 holes for plug diameter 8 mm, page 17, Å g. 3, arrow A.
Insert the fastening material you have purchased and screw the wall fastening plate to the wall tightly.
In the example with countersunk screws 5 x 70 mm, page 17, Å g. 3, arrow B.
Mounting fastening plate "3" on the TV set
Remove the stand base from the TV set if available. See Å g. 2 on page 17.
The retaining screws for the stand base are absolutely essential for the stability of the rear panel.
Screw in (4 screws) as shown on page 17, Å g. 2, arrows A and B for the LOEWE Connect 22 TV.
Screw in (2 screws) as shown on page 17, Å g. 2, arrows B for the LOEWE Connect 26 TV.
Take the fastening plate "3" and place it on the rear panel of the TV as shown on page 17, Å g. 2.
Screw the fastening plate and the TV rear panel together with the 4 fastening screws as on page 17, Å g. 3.
Marrying the fastening plate to the TV set with wall plate
Move the fastening plate "3" with the TV set over the wall plate so that it can be hooked into the capture bolts "a" of the join-
ted arm. See page 16, Å g. 1 and page 18, Å g. 5.
Tilt the TV set back at the top after hooking in. You can then install the insertion roller easily. See page 16, Å g. 1 and page 18,
Å g. 5.
Finally turn in the two threaded pins into the jointed arm on the right and left.
The threaded pins have a safety function and prevent the TV set from unhooking and falling.
9

Publicité

Table des Matières
loading

Table des Matières