Temperature Display; Putting Into Operation; Transporting The Appliance; Installing The Appliance - Atag KD8178BD Instructions D'utilisation Et De Montage

Putting into operation

(2) Fast Freeze button
(3) On/Off button, freezer
compartment
(4) - setting button, freezer
compartment
(5) + setting button, freezer
compartment
(6) Freezer compartment

temperature display

(7) Refrigerator compart-
ment temperature
display
3.2 Temperature display
The following are displayed in normal operation:
- the warmest freezing temperature
the average cooling temperature
-
The freezer compartment temperature display flashes:
- the temperature setting is being changed
after switch-on the temperature is not yet cold enough
-
the temperature has risen several degrees
-
Dashes flash in the display:
- the freezer temperature is above 0 °C.
The following displays indicate malfunction. Possible causes
and corrective action (see Malfunction).
- nA
- F0 to F5
4 Putting into operation

4.1 Transporting the appliance

CAUTION
Risk of injury and danger of damage as a result of incorrect
transport!
u Transport the appliance in a packed condition.
u Transport the appliance upright.
u Do not transport the appliance without assistance.

4.2 Installing the appliance

In the event that the appliance is damaged, contact the supplier
immediately before connecting to the mains.
The floor at the site must be flat and level.
Do not install the appliance in a location where it is exposed to
direct radiation of the sun, next to a cooker, heater and similar.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m
refrigerant used in the appliance. If the room in which the appli-
ance is installed is too small, a flammable gas-air mixture may
form in the event of a leakage in the refrigeration circuit. The
quantity of refrigerant used in your appliance is indicated on the
type plate on the inside of the appliance.
Fit the appliance in stable kitchen units only.
The following ventilation gaps must be observed:
The depth of the ventilation channel at the rear of the unit
q
must be at least 38 mm.
There must be a ventilation space of at least 200 cm
q
plinth and at the top of the unit.
30
(9) - setting button, refriger-
ator compartment
(10) + setting button, refriger-
ator compartment
(11) On/Off button, refrigerator
compartment
(12) Fast Cool button
(13) Fan button
per 8 g of R 600a
2
in the
2
Basically the principle applies: the larger the ventilation
q
space, the more energy-saving the appliance is in operation.
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
u The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
WARNING
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flam-
mable. Escaping refrigerant may ignite.
u Do not damage the piping of the refrigeration circuit.
WARNING
Fire hazard and danger of damage!
u Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
u Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
After installation:
u Remove the protective film from the decorative trims and
drawer fronts.
u Remove all transit supports.
u Unscrew the red transport
lock. Close the vacated
retaining hole using
stopper (60).
u Dispose of packaging material (see 4.5) .
Note
u Clean the appliance (see 6.2) .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u Always see to good ventilation at the installation site.

4.3 Changing the door hinges

NOTICE
Risk of damage to side-by-side appliances due to condensa-
tion!
When a side-by-side appliance (S...) is fitted together with a
second appliance (as a SBS combination), the door hinges
must remain as delivered.
u Do not change over the door hinges.
Make sure the following tools are to hand:
Spanner 13
q
Cordless screwdriver Torx® 15, 20, 25, 30
q
Slide the appliance 2/3 of the way into the recess.
Pull out the mains plug.
Open the doors.
the