LUND 67950 Instructions Originales page 12

All manuals and user guides at all-guides.com
GB
the appliance should be left to cool down for about 20 minutes . During cool-down, unplug the power cord from the power socket.
APPLIANCE OPERATION
CAUTION! Turn off the appliance and unplug the power cord from the socket during all equipment assembly and disassembly
activities.
Preparing for operation
Remove the product from its packaging, remove all parts and then wash all parts in contact with the food according to the instruc-
tions in the section entitled "Product maintenance".
Mixer assembly and disassembly
Place the drive housing on level and stable surface. Make sure that all suction cups in the base have attached themselves to the surface.
Place the mixer bowl on top of the drive housing so that the bowl's bottom edge is fully fl ush with the drive housing wall along
the entire circumference and the marker at the bottom edge of the bowl points to the open padlock symbol (X), and then rotate
the bowl so that the marker points to the closed padlock symbol (XI). The correctly installed bowl's lower edge is fl ush with the
entire circumference of the upper wall of the drive housing. A correctly mounted bowl cannot be dismantled except by turning it, so
that the marker indicates the open padlock symbol, and lifting. The drive housing has a safety device which, in case of improper
installation, will not allow to start the appliance rotation.
Place the spindle on the drive shaft inside the bowl (IV).
One of the following accessories can be attached to the spindle as required: grater holder with mounted grater, chopping blade,
kneading stirrer or whisker disc (V).
The grater must be mounted in the holder in such a manner that the hook at the rounded edge of the grater hits the gap in the
holder, and the axis of the holder passes through the opening in the grater (VI). Then press the grater into the holder so that the
upper surface of the grater is aligned with the upper surface of the holder. Due to the sharp edges of the grater, special care
must be taken when installing and removing the grater in the holder. It is recommended to use protective gloves during assembly.
Close the mixer bowl with the lid. Place the lid on the bowl so that it is fl ush with the mixer bowl along its entire circumference,
and the tab of the safety device is next to the handle of the mixer bowl (VII). Then rotate the lid in the direction indicated by the
closed padlock symbol (VIII).
The safety device will not allow the drive to start if the lid is removed or incorrectly mounted.
Insert the pusher into the lid inlet opening (IX). The pusher consists of two elements, an external and an internal one. The opening
in the external pusher can be used for placing small food products in the bowl.
Installation and removal of the blender cup
Place the drive housing on level and stable surface. Make sure that all suction cups in the base have attached themselves to the surface.
Place the cup on top of the drive housing so that the cup's bottom edge is fully fl ush with the drive housing wall along the entire
circumference and the marker at the bottom edge of the cup points to the open padlock symbol (X), and then rotate the cup so
that the marker points to the closed padlock symbol (XI). The correctly installed cup's lower edge is fl ush with the entire circumfer-
ence of the upper wall of the drive housing. A correctly mounted cup cannot be dismantled except by turning it, so that the marker
indicates the open padlock symbol, and lifting. The drive housing has a safety device which, in case of improper installation, will
not allow to start the appliance rotation.
Mount the lid on the cup so that it is fully fl ush with the edge of the cup along its entire circumference and the tabs inside the cup
hit the notches in the lid and then rotate the lid in the direction indicated by the closed padlock symbol (XII). The cup spout should
be covered by the lid tab in such a manner as to limit the possibility of spilling the contents of the cup.
The lid is equipped with a plug (XIII), which allows to add food ingredients while the blender is in operation. The plug can also be
used as a measure to dose the amount of ingredients.
Mill assembly and disassembly
Place the drive housing on level and stable surface. Make sure that all suction cups in the base have attached themselves to the surface.
Fill the container of the mill with food intended for grinding to half the height of the container. Screw the mill base onto the container
(XIV). The base thread is counterclockwise, so in order to connect the base with the container, hold the container and turn the base
counterclockwise. Removing the base and container will require rotation in the opposite direction.
Then rotate the assembled base and container 180 and place the mill base on top of the drive housing so that the base's bottom
O
edge is fully fl ush with the drive housing wall along the entire circumference and the marker at the bottom edge of the cup points
to the open padlock symbol (XV), and then rotate the base so that the marker points to the closed padlock symbol (XVI).
The safety device will not allow the mill to operate without the container or with the base of the mill incorrectly mounted on the base.
Using the appliance
CAUTION! Before using the appliance for the fi rst time, all parts which come into contact with food should be thoroughly washed
and dried. Please read the maintenance instructions beforehand.
O R I G I N A L I N S T R U C T I O N S
12