Regulatory Information; Contact Information - Aritech AD044 Manuel D'installation

If some AD044 outputs are not used, the linked output in the
ATS control panel must not be programmed (default).
Refer also to the ATS1290 manual for the direct link to the
zone number (control panel).
Memory location map
Every PID device has its own characteristics concerning
related I/O lines or certain functionality of the device.
A total of 16 memory locations are reserved to configure
the PID devices. Only the first nine are normally user
configurable. This depends on the functionality of the particular
device.
For the AD044 external PID interface only memory locations 3
and 5 matter.
On memory location 3, the zone type can be configured for
each input to single EOL, double EOL (default) or the zone can
be switched off (the status will always be "Normal").
On memory location 5, the output supervision can be enabled
(default) or disabled for each output.
Memory location map for AD044
Location Function Decimal values
3 Zone types For example:
0 = All zones are
Off
85 = All zones are
single EOL
170 = All zones
are double EOL
(default)
5 Supervision For Example:
outputs
0 = All output
supervisions
disabled
15 = All output
supervisions
enabled (default)
Zone type
Input loop Status ATS control
resistance panel
Double EOL
<20 Ω
Short
47 kΩ
Normal
94 kΩ
Alarm
> 1 MΩ
Open
Specifications
Bus protocol
Bus voltage
External power supply
Current consumption from bus
Unit load for DGP
Address range
Maximum current outputs
P/N 1051425 (ML) • REV E • ISS 11DEC20
Binary values
Zone 4: Bit 7–6
Zone 3: Bit 5–4
Zone 2: Bit 3–2
Zone 1: Bit 1–0
00 = Zone is Off
01 = Single EOL
10 = Double EOL
(default)
11 = Undefined
Output 4: Bit 3
Output 3: Bit 2
Output 2: Bit 1
Output 1: Bit 0
0 = Disabled
1 = Enabled (default)
Status ATS control
panel
Single EOL
Short
Normal
Open
Open
Point ID
12 or 24 V
12/24 V [1]
290 A
1
0 to 255
500 mA (each)
Single EOL resistor inputs
Double EOL resistors inputs
EOL resistors Outputs
Category
Device type
[1] The auxiliary power output of closest panel or DGP can also be
used.

Regulatory information

PLACED ON THE MARKET BY:
Manufacturer
Carrier Fire & Security Americas Corporation Inc.
13995 Pasteur Blvd
Palm Beach Gardens, FL 33418, USA
AUTHORIZED EU REPRESENTATIVE:
Carrier Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. CARRIER FIRE &
SECURITY CANNOT PROVIDE ANY
ASSURANCE THAT ANY PERSON OR ENTITY
BUYING ITS PRODUCTS, INCLUDING ANY
"AUTHORIZED DEALER" OR "AUTHORIZED
RESELLER", IS PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY INSTALL FIRE
AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Certification
Carrier Fire & Security hereby declares that this
device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.firesecurityproducts.com or
www.aritech.com.
REACH Product may contain substances that are also
Candidate List substances in a concentration
above 0.1% w/w, per the most recently published
Candidate List found at ECHA Web site.
Safe use information can be found at
https://firesecurityproducts.com/en/content/intrusi
on-intro
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info

Contact information

www.firesecurityproducts.com or www.aritech.com
For customer support, see www.firesecurityproducts.com
47 kΩ ±5%
2 x 47 kΩ ±5%
47 kΩ
I/O
T1
or scan the QR code.
3 / 10