Roadway, Area And Site Luminaire; Installation Instructions - Cooper Lighting Solutions XNV2 Instructions D'installation

INSTALLATION INSTRUCTIONS

IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Make certain power is OFF before starting installation or attempting any maintenance.
PHOTOCONTROL (IF EQUIPPED)
STEP 1. Using a flat blade screw driver, loosen the two flathead screws to allow rotation of
the receptacle.
STEP 2. Insert screwdriver into center slot and rotate receptacle until indicator arrow points
north or desired direction.
STEP 3. Tighten screws.
STEP 4. Insert the photoelectric control (or shorting cap) into receptacle and twist into locked
position.
NOTE: THE PHOTOCONTROL MUST CONTAIN A SOFT, RESILIENT GASKET FASTENED
TO THE BOTTOM SURFACE TO ASSURE A PROPER WEATHER SEAL BETWEEN THE
CONTROL AND THE RECEPTACLE.
ARM INSTALLATION (SQUARE POLE) FIG. 4
TOOLS REQUIRED: 1/2" open wrench, Phillips screw driver.
STEP 1. Insert nut plate into pole aligning holes on nut plate with mounting holes on the pole.
STEP 2. Insert threaded rods through top and bottom holes and screw them into nut plate.
STEP 3. Pull wires through center hole of back up plate and center hole of pole.
STEP 4. Make electrical connections between wires from pole and wires from the fixture.
STEP 5. Align top and bottom holes on the arm to slide over threaded rods. Arm should be
flush to the surface of the pole.
STEP 6. Push washers over the threaded rods and screw on nuts.
STEP 7. Using 1/2" open wrench tighten nuts.
STEP 8. Pass cover plate over arm. Align set screw holes on the cover and the arm and
tighten set screw.
ARM INSTALLATION (ROUND POLE) FIG. 5
TOOLS REQUIRED: 1/2" open wrench, Phillips screw driver.
STEP 1. Insert nut plate into pole aligning holes on nut plate with mounting holes on the pole.
STEP 2. Insert threaded rods through top and bottom holes and screw them into nut plate.
STEP 3. With the rounded end of the adapter facing the pole, align the holes on the adapter
with mounting holes on the pole. Push adapter over threaded rods.
STEP 4. Pull wires through center holes nut plate, pole and adapter and make wiring
connections.
STEP 5. Align top and bottom holes on the arm to slide over threaded rods. arm should be
flush with the flat surface of adapter.
STEP 6. Push washers over the threaded rods and screw on nuts.
STEP 7. Using 1/2" open wrench tighten nuts.
STEP 8. Pass cover plate over arm. Align set screw holes on the cover and the arm and
tighten set screw.
MAINTENANCE
NOTE: A REGULAR MAINTENANCE SCHEDULE SHOULD BE FOLLOWED TO RETAIN
OPTIMAL LIGHT OUTPUT AND THERMAL PERFORMANCE.
OPTICAL LENS CLEANING SHOULD BE PERFORMED WITH A CLEAN DRY CLOTH TO
REMOVE ANY DUST OR OTHER CONTAMINANTS. ADDITIONAL CLEANING CAN BE
PERFORMED WITH NON-ABRASIVE ACRYLIC CLEANSER.
REMOVE ANY DIRT, LEAVES OR OTHER FOREIGN DEBRIS FROM THE HOUSING AND
FINS. CLEAN WATER MAY BE USED TO FLUSH THE FINS.
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible
contingency during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user's purpose, please
contact your nearest representative. NOTE: Specifications and dimensions subject to change without notice.
Cooper Lighting Solutions
1121 Highway 74 South. Peachtree City, GA 30269
Washers
Cover Plate
Nuts
Arm
FIG. 4
Washers
Nuts
Arm
Cover Plate
FIG. 5
© 2020 Cooper Lighting Solutions. All Rights Reserved. Publication No. ADW131406 September 2013
www.cooperlighting.com
XNV2 LED
Roadway, Area and Site
Luminaire
Sheet 2 of 2
IMI-806
Threaded Rods
Backup Plate
Electrical Wires
Square Pole
Adapter
Threaded Rods
Backup Plate
Electrical Wires
Round Pole