Télécharger Imprimer la page

Jacuzzi J-300 Serie Manuel D'installation Et Utilisation & Entretien page 27

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 40
Adjusting PowerPro Jets
With the nozzles of the PowerPro Jets positioned straight ahead,
the jet stream will be stationary. Pushing the nozzle to one side
causes the jet nozzle to rotate, moving the jet stream in a circu-
lar pattern.
The jets may not spin with the pump on low speed.
Waterfall feature
The waterfall is on when the circulation pump is on. The JETS 1
or CLEARRAY buttons will also activate the waterfall feature.
Waterfall Operation Details
A. Push thumb wheel on top of waterfall to the left (while in s-
pa) to start or increase flow.
B. Push thumb wheel on top of waterfall to the right (while in
spa) to slow or turn flow off.
NOTE: When the waterfall is in the OFF position, some water could
still flow through.
Air controls
Some jets have a dedicated air adjustment button. Press down on
the side with the Jacuzzi logo to open. Press the opposite side to
close the air.
To minimize heat loss, all air controls (side with Jacuzzi logo up)
should be closed when the spa is not in use.
Certain jets may not dispense air when pump 1 runs at low speed.
Spa Stereo System (optional)
Spas equipped with the optional Jacuzzi audio system offer en-
hanced enjoyment.
Menu Features and Programming Instructions
Your spa is equipped with five menus that allow you to program ad-
ditional features. By continually pressing the Menu button you will
cycle through the menus as follows.
Current temperature (Main Menu)
Primary Filtration Menu
Secondary Filtration Menu
CLEARRAY/UV Menu
Economy Menu
Lock Menu
I
Primary Filtration Menu
During the primary filtration cycle, the circulation pump and
CLEARRAY are activated. The spa is programmed with a factory
default setting but can be programmed to any of the cycle set-
tings listed below. These cycles allow the circulation pump to
run for preset amounts of time per day, in addition to the normal
operation. Should the circulation pump activate outside of a p-
reset cycle (except for PF0 and PF6), e.g. when heating, that run
time will reduce the length of the next cycle.
Note: To set a time for the primary filtration cycle to begin, sim-
ply turn power on to the spa two minutes prior to the desired
time. You can also press the Warmer, Cooler and Jets Pump 1 but-
tons simultaneously for 2 seconds to restart the spa once pow-
er has been provided.
No filtration
4 hours of filtration per day
8 hours of filtration per day (default setting for
J-335/J-345/J-355/J-365/J-375/J-385)
12 hours of filtration per day
16 hours of filtration per day
20 hours of filtration per day
24 hours of filtration per day (default setting
for J-315/J-325)
2 hours of filtration – 4 times per day
3 hours of filtration – 4 times per day
A. (For Models J335/ J345/ J355/ J365/ J375/J385)
Two minutes after power is applied to the spa, an automatic pri-
mary filtration cycles begins. The circulation pump is activated
and set to run for 8 hours a day (factory default). The circulation
pump draws water through the skimmer bag and one of two fil-
ter cartridges to effectively remove small debris in your spa. Dur-
ing the primary filtration cycle, the circulation pump and CLEAR-
RAY are activated. The factory default setting is PF2. This setting
is programmable.
Note: The circulation pump also supplies heated water to the spa
when the heater turns on. Any time the circulation pump runs, e.g.
when heating, outside of a programmed cycle (except for PF0 and
PF6), that run time will reduce the length of the next cycle.
27

Publicité

loading

Ce manuel est également adapté pour:

J-315J-325J-335J-345J-355J-365 ... Afficher tout