Service Parts - NuTone QTNLEDB Instructions D'installation

INSTALL GRILLE
5. Finish ceiling.
Install ceiling material. Cut out around housing.
6. Plug in wiring.
Plug wiring into proper receptacles.
7. Attach grille to
housing.
Squeeze grille springs
and insert them into tabs
on each side of housing.
8. Push grille
against ceiling.
9. Remove light
lens.
Carefully insert a small
flat-blade screwdriver
between grille and lens.
Pry lens out.
10. Install light bulbs.
Purchase (2) 18W (max.),
type GU24 fluorescent
lamps with M.O.L.
(maximum overall length)
of 3.9" (100mm) as
illustrated below.
Insert lamps and bulb into
their sockets. Replace lens.
WARRANTY
BROAN-NUTONE THREE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects
in materials or workmanship for a period of three years from the date of original purchase. THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
During this three-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which
is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT
BULBS, FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty
does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse,
negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation
contrary to recommended installation instructions.
The duration of an implied warranty is limited to the three-year period as specified for the express warranty. Some states
do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE
PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE
FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT
USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This
warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number stated below, (b)
give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time
of requesting warranty service, you must present evidence of the original purchase date.
Broan-NuTone LLC, 926 W. State Street, Hartford, Wisconsin 53027 www.nutone.com 888-336-3948
DIAGONAL LED PLATE OPTION
To rotate LED plate to
1. Remove grille from ceiling and
2. Remove lens.
3. Remove three (3) screws from
4. Remove LED plate and rotate
5. Re-assemble grille assembly

SERVICE PARTS

3.9" (100mm) M.O.L.
* Not shown assembled.
Order service parts by "Part No." - not by "Key No."
diagonal position:
unplug wiring from housing.
retention ring.
plate clockwise to diagonal
position.
and re-install to fan housing.
KEY NO. PART NO.
1 SQTHB1 HANGER BAR KIT
2 475 DUCT REDUCER 6" TO 4"
3 97018562 DUCT CONNECTOR - 6"
4 99111293 SPACER (2 REQ'D)
5 97016466 HOUSING
6 98010102 WIRING PLATE
7 99170245 SCREW, #8-18 X .375
8 97018552 WIRE PANEL/HARNESS ASSEMBLY
9 97020045 CONTROL ASSEMBLY
10 97020046 SERVICE ASSEMBLY, BLOWER
(INCLUDES KEY NO. 11)
11 99420665 THUMBSCREW, #8-18 X .375
12 99140199 GRILLE SPRING (2 REQ'D)
13 97018561 GRILLE ASSEMBLY
14 99271381 BULB, GU24, 18W FLUORESCENT (2 REQ'D)
15 99111532 RING
16 99111529 LENS
MODEL QTNLEDB
LENS
SCREWS
RETENTION
RING
Replacement parts can be
ordered on our website.
Please visit us at
www.nutone.com
SERVICE NOTE
To remove Blower
Assembly: Unplug motor.
Remove thumbscrew (11)
from motor plate flange.
Find the single TAB on the
motor plate (located next
to the receptacle). Push
up near motor plate tab
while pushing out on side
of housing. Or insert a
straight-blade screwdriver
into slot in housing (next to
tab) and twist screwdriver.
DESCRIPTION
99045485B
Page 4
LED
PLATE
GRILLE