Publicité
explicitly described in this manual) should be carried
out only by authorised service centres or by special-
ised technical personnel who are experts in the sec-
tor and in the pertinent safety regulations.
☞ The machine owner can only use original acces-
sories and spare parts supplied exclusively by the
manufacturer since such parts are the only ones that
guarantee that the equipment will operate safely
without any problems. Do not use parts disassem-
bled from other machines or other kits as spare
parts.
If the machine will no longer be used, remove the
batteries and dispose of them in accordance with the
eco-compatibility regulations as set forth in European
standard 91/157/EEC or deposit them in an author-
ised collection centre.
To dispose of the machine, comply with the current
laws where it is used:
- disconnect the machine from the mains and clean it
after emptying any liquids;
- separate the machine into groups of homogeneous
materials (plastics in accordance with the recycling
symbol, metals, rubber, packing). For parts contain-
ing different materials, contact the competent au-
thorities;
Each homogeneous group must be disposed of in
accordance with recycling laws.
In addition, it is recommended to eliminate those
parts of the machine that may be dangerous, espe-
cially for children.
☞ Before each use, check the machine and, in par-
ticular, check that the battery charging cable and the
connector are in good condition and safe for use.
If they are not in perfect condition, do not use the
machine for any reason until an authorised specialist
repairs the defective parts.
☞ If foam or liquid is noted, immediately turn off the
suction motor.
☞ Do not use the machine on textile flooring, such
as rugs, carpeting, etc.
Wax, foaming detergents or dispersions along the
hoses may cause serious problems for the machine
or clog the hoses.
3.2
NOISE AND VIBRATIONS
See the last page.
4. HANDLING INFORMATION
4.1
PACKING LIFTING AND TRANSPORT
• During all lifting or transport operations, make sure
that the packed machine is securely anchored to pre-
vent it from tipping over or falling accidentally.
Transport vehicle loading and unloading operations
must be carried out with adequate lighting.
The packed machine must be handled using adequate
devices, making sure not to damage/strike any part of
the packing, not to tip it over and to be very careful
when placing it on the ground.
☞ All these instructions also apply to the batteries and
the battery charger.
4.2
CHECKS UPON DELIVERY
☞ When the goods are delivered (machine, bat-
tery or battery charger) by the transporter, carefully
check the condition of the packing and its contents.
If the contents have been damaged, notify the trans-
porter and reserve the right, in writing (select the
word "reserve" on the document), to submit a claim
for compensation before accepting the goods.
4.3
UNPACKING
• Wear safety clothing and use adequate tools to limit the
risks of accidents.
Carry out the following steps if the machine is packed with a
cardboard housing:
- Use scissors or clippers to cut and eliminate the plastic straps.
- Slip off the cardboard housing from the top of the packed
machine.
- Remove the envelops inside and check their contents (use and
maintenance manual, battery charger connector)
- Remove the metallic brackets or plastic straps that secure the
machine to the pallet.
- Release the brushes and the squeegee from the packing.
- Take the machine off the pallet (pushing it backward) by
using an inclined surface that is solidly attached to the floor
and to the pallet.
If the machine is packed in a wooden crate:
- Detach all the wooden sides from the pallet, starting from
the top one.
- Remove the protective film wrapped around the machine.
- Remove the metallic brackets or plastic straps that secure the
machine to the pallet.
- Release the brushes and the squeegee from the packing.
- Take the machine off the pallet (pushing it backward) by
using an inclined surface that is solidly attached to the floor
and to the pallet.
Take the same precautions and follow the same instructions to
remove the optional battery charger from the packing (holding
the special handles to extract it from the top of the packing)
and the optional battery.
After moving the machine away from all the packing, start
mounting the accessories and the batteries as per the instruc-
tions provided in the specific section.
Keep all the pieces of the packing since they might be useful in
the future to protect the machine and the accessories during
transport to another location or to authorised service centres.
If not, the packing can be disposed in accordance with current
disposal laws.
4.4
ASSEMBLY AND ADJUSTMENT OF
THE GRIP
- Insert the grip in its seat.
- Fix the grip at the desired height and screw the 2
knobs (Foto B-21*).
- Fit the suction hose in its seat on the recovery tank
(Foto B-3*).
- Connect the Anderson safety connector (Foto
B-18*)to its socket (Foto B-17*)
29
Publicité
