Annovi Reverberi BLUE CLEAN M20 Traduction Des Instructions Originales page 20

ENGLISH
4 GENERAL INFORMATION (PAGE 3)
4.1 Use of the manual
This manual forms an integral part of the appliance and should be kept
for future reference. Please read it carefully before installing/using the
unit. If the appliance is sold, the seller must pass on this manual to the
EN
new owner along with the appliance.
4.2 Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig. 1.
4.2.1 Documentation supplied with the appliance
D1 Use and maintenance manual
D2 Safety instructions
D3 Declaration of conformity
D4 Warranty regulations
4.3 Disposing of packaging
The packaging materials are not environmental pollutants but must still
be recycled or disposed of in compliance with the relevant legislation
in the country of use.
5 TECHNICAL INFORMATION (PAGE 3)
5.1 Intended use
The appliance is intended for use as a multi-purpose vacuum cleaner,
in compliance with the descriptions and safety precautions contained
in these instructions.
This appliance is designed for household use only and must not
be utilised for industrial or commercial purposes.
The appliance conforms to the IEC 60335-1 and IEC 60335-2-2
standards.
5.2 Operator
The symbol shown in fig. 1 identifies the appliance's intended
operator (professional or non-professional).
5.3 Main components:
A1 Starter device
A2 Suction connection
A3 Blower connection
A4 Handle
A5 Power cable stowing hook
A6 Catches
A7 Power cable with plug
A8 Castor wheels
A9 Tank
A10 Cover with motor
A11 Accessories holder
5.3.1 Accessories (see fig. 1 for details of models - supply
package is as shown on the cardboard box)
B1 Filter holder
B2a Cartridge filter
B2b Sponge filter
B3a Hose
B3b Hose
B5a Tube
B5b Tube
5.4 Safety devices
- Starter device (A1)
The starter device prevents accidental use of the appliance.
20
(Original instructions)
B6 Floor brush
B7 Carpet - upholstery brush
B8 Crevice nozzle
B9 Round brush (where featured)
B10 Fabric filter bag (where featured)
B11 Paper filter bag (where featured)
B12 Tube hook
6 INSTALLATION (PAGE 4)
Warning - danger!
All installation and assembly operations must be performed with the appliance
disconnected from the mains power supply.
The assembly sequence is illustrated on page 4.
6.1 Assembly
When unpacking, check for any missing accessories or damage to the
contents. If damage caused in transit is found, notify your dealer at
once.
Lift the cover with the motor (A10) off the appliance, releasing the
catches (A6) and take out the accessories supplied, checking that
the filter (B2a/B2b) is fitted correctly. For liquids use the sponge filter
(B2b).
See fig. 2
The assembly sequence is illustrated on page 4.
6.2 Fitting the castor wheels
Turn the vacuum cleaner tank (A9), with the cover off, upside down
on a firm horizontal surface. Fit the castor wheel hubs (A8) into the
holes provided and press fully down to secure the wheels in the
correct position.
See fig. 3
6.3 Fitting the accessories
Connect the hose (B3a/B3b) to the suction (A2) or the blower
connection (A3) depending on the type of operation required.
See fig. 4
6.3.1 Dry suction/Sucking in liquids/Blower function
Then complete the sequence with the accessories required
for the type of cleaning job planned. Use the tubes (B5a)
and the brushes (B6-B7-B8-B9) depending on the type of
cleaning and the surface to be cleaned. The brushes (B6-B7-
B8-B9) can be fitted straight onto the hose (B3a).
See fig. 5
6.3.2 Sucking in cold ash/Blower function
Then complete the sequence by connecting the hose (B3b)
to the tube (B5b).
See fig. 5
6.4 Electrical connection
Warning - danger!
Check that the electricity supply voltage and frequency (V/Hz)
correspond to those specified on the data plate. See fig. 6.
6.4.1 Use of extension cables
Use cables and plugs with "IPX4" protection level.
The cross-section of the extension cable should be
proportionate to its length; the longer it is, the greater its
cross-section should be.
7 INFORMATION ON USE OF THE APPLIANCE (PAGE 5-6)
7.1 Controls
- Starter device (A1). See fig. 7.
Set the starter device switch on (ON/I).
If there is a pilot light on the starter device, it should light up.
Set the starter device switch on (OFF/0) to stop the appliance.
If there is a pilot light on the starter device, it should go out.
Warning - danger!
During operation the appliance must be positioned as shown on a firm,
stable surface. See fig. 8.