Series D80000 Stainless Steel Hose Reels
INSTALLATION INSTRUCTIONS
WARNING: Ensure that reel, hose, and
equipment are properly grounded. Use an
ohmmeter to check ground continuity.
Mounting
CAUTION: Unless reel was specified
differently when ordering, maximum
installation height is 16 feet. Do not exceed
this distance.
Maximum Operating Temperature:
Low pressure (300 psi) = 150°F (66°C)
1.
Unpack and inspect reel for damage.
Turn by hand to check for smooth
operation. Check for completeness.
2.
Configure reel for top, side or bottom
hose dispensing by removing the bolts
(2) from one side of the guide roller
bracket and loosening the four guide arm
bolts (3) on each side of the hose reel.
Rotate and remove each guide arm then
reinstall in the desired configuration. If
bottom wind is desired, bolts (13) and
bolts (2) must be removed and replaced
after the guide arm is in position.
:
CAUTION
When changing guide arm
positions, the U-bolt must be placed in the
proper location as instructed in figure A.
The reel can "latch out" during use if this
instruction is not adhered to.
3.
Position reel on floor, wall, or ceiling.
Secure into place using four (customer
supplied) bolts.
Installing the Input Hose
WARNING: Ensure that supply line pressure
does not exceed maximum working pressure
rating of reel. Apply pipe thread sealant to all
Page 2
threads on standard reels. Do not overtighten
connection. Recommended torque not to
exceed 70 ft. lb.
CAUTION
Use flexible hose connection at
:
input. Do not use rigid plumbing.
1.
Apply thread sealant as directed and
connect swivel (12) to main shaft input
(5).
2.
For standard shaft and swivel reels,
connect customer supplied inlet hose (4)
to swivel input as indicated in illustration.
Installing the Output Hose
WARNING
Use extreme caution; reel under
:
tension. Avoid releasing latch mechanism.
CAUTION
Apply pipe thread sealant to all
:
threads on standard reels. Do not overtighten
connection. Recommended torque not to
exceed 70 ft. lb.
1.
Manually turn sheave (6) until spring is
tight, back off 3 turns, then latch.
2.
Route output hose (7) through roller
bracket (1), U-bolts (8), then through
cutout (9) in spool as indicated in
illustration.
3.
Connect output hose (7) to gooseneck
(10) as indicated in illustration.
4.
Verify U-bolt position conforms with
guide arm position using label inside
spool. Then tighten nuts (11) on U-bolt
(8).
5.
Charge hose. Momentarily open control
valve to purge hose of gases. When fluid
appears at control valve, close valve.
With hose fully charged, release latch and
wind output hose onto reel.
6.
Install bumper stop assembly.
ADJUSTMENTS
WARNING: Use extreme caution; reel under
tension. Avoid releasing latch mechanism.
If necessary, adjust spring tension on reel by
manually adding or removing wraps of hose
from spool, one wrap at a time, until desired
tension is obtained. Manually add wraps to
increase tension. Remove wraps to decrease
tension.
CAUTION: When adding wraps of hose, add
just enough wraps to acheive the desired
tension without exceeding the winding
mechanism's spring capacity. Properly
tensioned reels allow all hose to be freely
removed from the spool until the point of
U-bolt contact. Damage to the winding
mechanism will result if spring is over-
tensioned.
SERVICE INSTRUCTIONS
User servicing of the reel is limited to
replacing input/output hoses only. Refer all
other repairs to an authorized service person
or directly to Reelcraft. Failure to do so may
result in personal injury and/or equipment
damage and may void the warranty.
WARNING: Rewind hose on reel, then bleed
pressure from system before performing the
following procedures.
CAUTION: Remove all spring tension before
disassembling the hose reel. Do not attempt to
open the riveted spring case assembly.
1.
Replace hoses in accordance with
procedures given in "Installation
Instructions" section of this manual.
2.
All mating moving parts have been
factory lubricated as required.
Figure A
www.reelcraft.com