Wood's M10G Manuel De L'utilisateur page 6

Thank you
Thank you for choosing a Wood's
dehumidifier. You are one of more
than 600.000 people who have cho-
sen a Wood's dehumidifier to prevent
damages from excessive moisture
and mould. Originating in Canada in
1950, Wood's has more than 60 years
experience of developing and manu-
facturing dehumidifiers. When choo-
sing a Wood's dehumidifier you'll get
a unit with great quality, high capacity
and that will extract the most litres per
consumed kWh.
Workings of your
dehumidifier
The Wood's M10G is a compressor
dehumidifier. As the air is drawn
through the dehumidifier by the fan,
the air passes over the compressor
cooled copper coils. The coils cool the
water vapour, separating the water
from the air.
The water drips down from the coils
and is drained away with the water
hose. Left is the dry air that is exhau-
sted in the room. As the dehumidifier
condensates the water vapour, heat
energy is released. That is why a
compressor dehumidifier will exhaust
dry air that is extra beneficial for dry-
ing clothes, laundry, wood etc.
A compressor dehumidifier is the
most energy efficient way to remove
excess moist and bad odour. Keep
the relative humidity level between
50% and 60% to maintain a safe and
healthy indoor environment.
1. Installation and
placement
Wood's dehumidifiers are easy to
move around, but bare in mind the
following.
• The dehumidifier should not be
placed near radiators or other
heat sources or exposed to direct
sunlight, as it will reduce its perfor-
mance.
• Keep at least 25cm distance from
walls and other obstructions to max-
English
imize the air flow.
• For optimum performance, place
the dehumidifier in the middle of the
room.
• Make sure that the air flow from the
inlet and outlet isn't blocked
Installation:
1. Place the dehumidifier on a flat and
solid ground, preferably in the middle
of the room.
2. Close all windows and ventilators
in the room. Otherwise, moist air from
the outside will continue to flow into
the room.
3. Connect the dehumidifier to a
grounded power outlet.
If the dehumidifier is transported
horizontally, oil may have run out of
the compressor and into the closed
piping system. In such a case, let
the dehumidifier stand for a few
hours before being used. It is very
important that the oil runs back into
the compressor, otherwise the dehu-
midifier may be seriously damaged.
2. Using the M10G
Hygrostat controlled
The unit will run only when the
ambient humidity exceeds your set
value.
Automatic restart
In the event of a power failure, the
unit will continue to work according to
your latest settings once the power
returns.
Automatic defrost
The unit will defrost automatically
when needed and resume to work
when the defrost is completed.
When defrosting, the compressor
shuts off and the defrost indication
light is lit.
Start and stop the dehumidifier by
pressing the ON/OFF button.
When the compressor is working, the
compressor light is illuminated.
6
Set desired humidity
Press the UP and DOWN arrows
to choose desired humidity level
between 30% and 90%. The dehu-
midifier will shut off when desired
humidity level is reached. Set value
is shown in the display for a couple of
seconds. After, the display returns to
showing the ambient humidity level.
Press the DOWN arrow until the dis-
play shows CO to have the dehumi-
difier running continuously. Continue
function, no matter room humidity,
machine continue running.
When ambient humidity level is below
35%, the display shows LO. When
ambient humidity level is above 95%,
the display shows HI.
NOTE: when desired humidity level is
reached, the fan will continue to work
for a couple of minutes before shut-
ting off .
Set timer for automatic shut off
Press the timer button repeatedly to
active the timer for automatic shut
off between 1 and 24 hours. When
activated, the timer light illuminates.
Set value is shown in the display for a
couple of seconds. After, the display
returns to showing the ambient humi-
dity level. Press the timer button until
the display shows 0 and the timer
light shuts off to deactivate. When
shut off due to the timer, you need to
press the power button to restart the
unit.
4.Water drainage
When the water reservoir is full, the
dehumidifier is shut off automatically.
Once the water reservoir is emptied
the unit will automaticallt restart.
1. Disconnect the dehumidifier from
the power source.
2. Empty the water reservoir.
3. Put the empty water reservoir back
and check that the float moves
freely.
4. Connect the dehumidifier to the
power source.