Publicité
Les langues disponibles
Les langues disponibles
DESCRIPTION
The hood may be in the filtering or the ducting version. Filtering version (Fig. 1): The hood aspirates the
kitchen air saturated with fumes and odours, purifies it through the grease filters and charcoal filters and returns
clean air into the room. For constant efficiency, the charcoal filters must be replaced periodically. The charcoal
filters are not supplied.
Ducting version (Fig. 2): The hood aspirates the kitchen air saturated with fumes and odours, passes it through the grease
filters and expels it to the outside through an outlet pipe. With this version the charcoal filters are not required. Decide
from the outset on the type of installation (filtering or ducting). For greater efficiency, we recommend you install the hood
in the ducting version (if possible).
INSTALLATION
ATTENTION: Two persons are required for proper installation; the unit should be installed by a qualified operator.
1.
Features of the outlet pipe (only for the ducting version): Before fixing, the outlet pipe for air evacuation
to the outside must be installed. Use an outlet pipe with: – minimum indispensable length; – minimum possible bends
(maximum angle of bend: 90°); – certified material (according to the State); – an as smooth as possible inside. It is also
advisable to avoid any drastic changes in pipe cross-section (recommended diameter: 150 mm). For air evacuation to
the outside, follow all the other instructions given on the "Warning" chapter.
2.
Prepare the electric power supply (for the electric connection, follow all other indications stated on the
"Warning" chapter). Prepare the electric power supply within the decorative flue.
3.
Assembly of the flange (only for the ducting version): install the flange in the device air outlet and press
slightly (Fig. 3).
4.
Fitting the lateral heads (optional): the heads are fixed to the sides of the hood, each with 3 screws (Fig. 4).
5.
Removing the grease filter: Open the front panel, gripping it by the lower part and turn it outwards to the end
of its travel (Fig. 5) then gently release it until it locks. Remove the grease filter by pushing the catch and turning it outwards.
6.
Fixing to the wall: Draw a line on the wall in vertical line with your hob. Mark the first 4 holes to be drilled in the
wall, respecting the distances indicated in Fig. 6. Drill the 4 holes and fit the screw anchors provided. Fix the metal brackets
(A) to the wall using the holes just drilled (Fig. 7); the screws for fixing the bracket are provided.
Hang the hood on the brackets (Fig. 8). Adjust the horizontal position moving the hood to the right or left so that it is aligned
with the wall units. When adjustment has been completed, without removing the hood, mark the other 2 holes to be drilled
(C) in the wall. Remove the hood and drill the holes marked (8 mm diameter). Then use the 2 screw anchors and the 2
screws provided for final fixing.
7.
Fixing of the telescopic decorative flue: Adjust the width of the support bracket (D) of the telescopic flue by
means of the screws (E) as shown in Fig.9; then, by means of the screw anchors and screws (F) provided, fix the bracket
to the ceiling in such a way that it is positioned along the axis with your hood.
- Only for the ducting version: Connect the air outlet pipe to the air vent of the hood. Use a flexible pipe and lock it to
the air vent of the hood with a metal hose clamp - Fig. 10 (pipe and clamp are not provided).
- Only for the filtering version: Mount the flange on the hood in correspondence to the air outlet point (Fig. 11). Take the
air baffle and fit a flexible pipe to it (125 mm diameter) locking it with a metal hose clamp (pipe and clamps are not provided).
Fit the air baffle to the upper flue (Fig. 12) with 4 screws. Connect the flexible pipe to the flange on the air vent (Fig. 13).
- Carry out the electrical connection of the hood using the power supply cable.
- Insert the extension flues setting them on the hood; extend the upper flue to the ceiling and secure with the 2 screws
(H) - Fig. 14.
8.
Assembly of the charcoal filter (only for the filtering version): check that the charcoal filters have already
been installed. Rest them on the sides of the motor and turn them in an anti-clockwise direction (Fig. 15).
OPERATION
DESCRIPTION OF THE KEYS AND FUNCTIONS (Fig. 16):
The appliance is equipped with a completely automatic system (Advanced Sensor Control) capable to manage
all the functions of your hood. Thanks to the ASC, the air in the kitchen is costantly clean and odour free
without any manual intervention. The advanced sensor catches all sort of vapours, smokes and odours caused
by the cooking process. The ASC also captures an abnormal presence of GAS. To access this function, press
the key "A" (see point 1 of the instructions).
The hood also features numerous other functions that you can choose according to your needs and preferences.
Using the "MENU" key, you can access the selection methods, and pressing the - and + keys you can search
for the function you want to activate (the function flashes on the display); once you have made your selection, activate
it by pressing "ok". To exit from the Menu, press the "MENU" key again.
To activate/disactivate the hood motor, press the - key (or + key) and select the desired speed.
List of the functions on the Menu :
- MINUTE COUNTER WITH BUZZER: The hood is equipped with a minute counter that emits an acoustic signal when
the time has elapsed. To activate this function, see point 3 of the instructions.
Publicité
