Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Mounting Bracket Installation
Bracket-A
Bracket-B
1. Mount Bracket-A to downdraft body. Screws are in place on
downdraft body.
2. a) Mount Bracket-B to Bracket-A. Position short leg of "B"
against "A" for mounting to front or rear of cabinet. This
results in minimum extension of bracket positioning.
HINT: Pre-drive screws into Bracket-A.
b) Position long leg of "B" against "A" for maximum
extension of bracket position.
Positioning will be determined by final location of the
downdraft in the cabinet/counter top.
3. To fasten Bracket-B to cabinet, assemble "B" to "A"
per instruction (Item-2). Snug screws to allow "B" to be
positioned against cabinet (front or rear). Position downdraft
intake unit in its final position in countertop. Secure screws
holding Bracket-B to "A". Use wood screws (not provided) to
secure Bracket-B to front and rear of cabinet.
NOTE: The mounting brackets must be secured to the cabinet,
front and rear. The front of the cabinet must have a secure wood
surface to mount the bracket to. Depending on the cabinet
construction a wooden brace (1 x 2 or equivalent) may be
required to be added to the cabinet. Determine planned position
of downdraft in cabinet and secure brace to cabinet.
INSTALLATION INSTRUCTIONS
Downdraft
Cabinet
Wood Brace
Install Foam Strips
1. If the right side of the downdraft is positioned against the
countertop, remove and discard the bridge, do not remove
screws.
If the right side of the downdraft is positioned adjacent to a
cooktop, adjust the position of the bridge bracket to be level
with the top of the countertop.
NOTE: The bridge kit included with a 15" (38.1 cm) module
cannot be used on the right side of the downdraft. The
bridge bracket provides the required foam strip surface.
2. Install foam strips, cut to size, on the counter top (front and
rear) and left side supporting surface (bridge kit or counter
top) and on the downdraft bridge bracket.
Recirculation (Non-ducted) Installation
Cabinet Cutouts for Non-ducted Installations
1. After laying out the positioning of the desired cooktop and
downdraft units to be installed determine the location of the
centerline of the downdraft intake. Mark out the required cut
out in the cabinet floor and kick plate. It is recommended
that the complete layout of downdraft and cooktop(s) be
established before cutting any openings.
2. Countertop and cabinet can now be cut to the prepared
requirements.
3. Assemble the 6" (15.2 cm) round elbow to 6" (15.2 cm) -
3
/
" x 10" (8.3 cm x 25.4 cm) transition (stack boot) to
1
4
3
1
/
" x 10" (8.3 cm x 25.4 cm) elbow to recirculating
4
assembly.
Secure all joints and seal using the aluminum metal duct
tape. This assembly can now be dropped into the opening in
the cabinet floor.
4. Secure the recirculation assembly to the kick plate.
5. Assemble the blower to the pedestal using supplied brackets
and use wood screws (not supplied) to secure blower to
pedestal.
6. Position assembly from item-5 onto cabinet floor to engage
6" elbow on assembly from item-3. Secure joint and seal
with aluminum duct tape.
7. Position prepared downdraft intake into cabinet and engage
with blower assembly intake. Secure and seal duct joints
8. Anchor the pedestal to the cabinet floor with wood screws.
9. Assemble the downdraft mounting brackets previously
described.
10. Assemble the recirculation cover to the recirculation
assembly in the cabinet kick plate.
11. Option: The opening in the cabinet floor can be covered to
trim out the cabinet interior.
Downdraft Intake
Gasket (Foam Strip) Surface
Bridge Bracket
Adjusting Screw
Adjusting Direction
(Bridge Bracket)
11
Publicité
Table des Matières
