Technical Data - Steinbach Classic 250N Mode D'emploi

Operation with a pool vacuum cleaner (Illustration 9)
■ The pool vacuum cleaner's hose can be connected directly to the fi lter
system's suction pipe. In doing so, the pool vacuum cleaner's hose must be
completely fi lled with water.
■ The use of a skimmer with a strainer basket is recommended for fi lter systems
without pre-fi lters.
■ Please observe the pool vacuum cleaner's operating instructions. To prevent
the fi lter from running dry and thus overheating, no air should be allowed to
enter the fi lter system.
■ Please select the "FILTERN" position on the valve head.
■ Alternatively, you can also select the "ENTLEEREN (empty)" position, for
example if algae forms in the pool. Dirty pool water will not then run back
into the pool, but will be directly channelled away via the waste pipe. When
selecting this setting, it is necessary to re-fi ll your pool to the correct level after
cleaning, if necessary.

Technical data:

040385 Classic 250
■ Filter pump: 040955
■ Circulation power 3,800 l/h
■ Pump is not self-priming
■ maximum water temperature 35 °C
■ 230 V / 200 W
■ 7 way valve with pressure gauge
■ Tank Ø 250 mm
■ Connector Ø 32/38 mm
■ Base plate
■ requires approx. 10 kg sand
■ recommended grain size 0.7 - 1.2 mm
■ for pools up to 19,000 l capacity
■ Optional: Speedpart Container for UV system Speed UV
040310 Classic 310
■ Filter pump: 040921
■ Circulation power 3,800 l/h
■ Self-priming pump with pre-fi lter
■ Maximum water temperature 35 °C
■ 230 V / 250W
■ 7 way valve with pressure gauge
■ Tank Ø 320 mm
■ Connector Ø 32/38 mm
■ Base plate
■ Requires approx. 20 kg sand
■ Recommended grain size 0.7-1.2 mm
■ For pools up to 22,000 l capacity
■ Optional: Speedpart Container for UV system Speed UV
040340 Classic 400
■ Filter pump: 040920
■ Circulation power 6,600 l/h
■ Self-priming pump with pre-fi lter
■ Maximum water temperature 35 °C
■ 230 V / 450W
■ 7 way valve with pressure gauge
■ Tank Ø 370 mm
■ Connector Ø 32/38 mm
■ Base plate
■ Requires approx. 25 kg sand
■ Recommended grain size 0.7-1.2 mm
■ For pools up to 33,000 l capacity
■ Optional: Speedpart Container for UV system Speed UV
Changing the fi lter sand
The fi lter sand should be changed every 2-3 years, depending on how much the
fi lter system is operated.
Care instructions
Visible impurities are removed via the fi lter system. However, this does not
apply to algae, bacteria and other micro-organisms, which are also a constant
threat to clear, clean and healthy swimming pool water. For their prevention
or removal special water care products are available, which when dosed
correctly and regularly do not cause any irritation
for bathers and guarantee hygienically perfect water for swimming.
Cleaning
Turn the fi lter system off before cleaning and pull out the mains plug. Use
conventional cleaning products. Do not use solvent based or abrasive cleaning
agents, i.e. no hard sponges, brushes etc..
h
Storage
The product must be thoroughly dried after cleaning. After which, it is to be stored in
a dry location protected from frost (5-8°C).
Disposal
Disposing of packaging: The packaging material has been selected in view of
environmental concerns and disposability and is therefore recyclable. The paper
and cardboard can be recycled, as can the plastic coverings.
Warranty conditions
The respective country's legal provisions for warranty conditions shall apply
accordingly.
250N/310/400_040385_040310_040340_v1911
Disposing of the product: Applicable in the European Union and
other European states with systems in place for collecting and
sorting recyclable materials. Dispose of the product in accordance
with any laws and regulations applicable at your place of residence.
Old devices must not be placed in the household waste! Should
the robot become unusable, each customer is legally obligated
to separate old devices from the household waste, e.g. take the
device to your community/ area collection point. It is therefore ensured
that old devices are professionally recycled and negative effects on
the environments are mitigated. For this reason, electrical devices are
marked with the symbol depicted here.
EN
9