Special Safety Instructions; Noise And Vibration; Operating Instructions; Adjusting The Auxiliary Handle - Flex DH 5 SDS-max Mode D'emploi

Special safety instructions

 Do not work on cut materials which release
hazardous substances (e.g. asbestos).
Take precautions if hazardous, combu-
stible or explosive dust is likely to occur.
Wear protective dust mask. If available,
use dust extraction equipment.
 Identify the power tool with stickers only.
Do not drill any holes into the housing.
 The mains voltage and the voltage
specifications on the rating plate must
correspond.

Noise and vibration

The noise and vibration values have been
determined in accordance with EN 60745.
The A evaluated noise level of the power tool
is typically:
– Sound pressure level:
– Sound power level:
– Uncertainty:
Total vibration value (when chiseling):
– Emission value:
– Uncertainty:
^qqbkqflk>
qÜÉ=áåÇáÅ~íÉÇ=ãÉ~ëìêÉãÉåíë=êÉÑÉê=íç=åÉï=
éçïÉê=íççäëK=a~áäó=ìëÉ=Å~ìëÉë=íÜÉ=åçáëÉ=~åÇ=
îáÄê~íáçå=î~äìÉë=íç=ÅÜ~åÖÉK
klqb>
The vibration emission level given in this infor-
mation sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another.
It may be used for a preliminary assessment
of exposure. The declared vibration emission level
represents the main applications of the tool.
However if the tool is used for different applica-
tions, with different accessories or poorly main-
tained, the vibration emission may differ.
This may significantly increase the exposure level
over the total working period.
For a precise estimation of the vibration load the
times should also be considered during which the
power tool is switched off or even running, but not
actually in use.
14
89 dB(A);
100 dB(A);
K = 3 dB.
2
a = 11.5 m/s
h
2
K = 1.5 m/s
This may significantly decrease the exposure level
over the total working period.
Identify additional safety measures to protect
the operator from the effects of vibration such as:
maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
`^rqflk>
tÉ~ê=É~ê=éêçíÉÅíáçå=~í=~=ëçìåÇ=éêÉëëìêÉ=
~ÄçîÉ UR=Ç_E^FK

Operating instructions

Before switching on the power tool
Unpack power tool and accessories and check
that no parts are missing or damaged.

Adjusting the auxiliary handle

t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=ÉäÉÅíêáÅ=
éçïÉê=íççäI=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
`^rqflk>
rëÉ=ÉäÉÅíêáÅ=éçïÉê=íççä=ïáíÜ=~íí~ÅÜÉÇ=~ìñáäá~êó=
Ü~åÇäÉ=çåäóK
The auxiliary handle can be swivelled into any
position to ensure safe and fatigue-free
working.
 Loosen the clamping screw by turning
it anti-clockwise.
 Swivel the auxiliary handle into the required
position (radial, axial).
 Retighten the auxiliary handle by turning
the clamping screw clockwise.
DH 5 SDS-max