Important Safety Instructions For Battery Charger - Metabo HPT SV 1813DA Manuel D'instructions

16. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
17. ALWAYS wear eye protection that meets the
requirement of the latest revision of ANSI
Standard Z87.1.
18. NEVER leave the random orbit sander on a table, the
fl oor, etc. while it is spinning.
19. NEVER apply water or lubricating oil, otherwise
hazards from electrical shocks may result.
20. NEVER push the random orbit sander too strongly
onto a surface.
Pushing the random orbit sander too strongly may
cause the sanding paper to tear or shorten the life of
the sander itself.
21. ALWAYS operate the random orbit sander safely for
correct use.
This random orbit sander is a portable dry plane
surface sander that was designed for fi nishing wood
and metal surfaces and ground coats.
22. Make sure that there are no cracks, scratches, or
other abnormalities on the pad before use.
23. Use the sanding paper and accessories specifi ed by
metabo HPT.
24. Do not leave the tool running. Operate the tool only
when hand-held.
25. When operating the tool, do not wear work gloves as
such cloth wear can get caught in the tool.
26. When working at elevated locations, clear the area of
other people and aware of conditions below you.
27. When sanding metal, sparks are generated. Do
not use the dust bag, and keep other persons and
fl ammable substances away from the work area.
28. ALWAYS wear a protective mask when operating the
random orbit sander.
Ventilate your work area adequately when you
perform sanding operations.
29. Defi nitions for symbols used on this tool
V ..................volts
— --- ............. direct current
n
o ...............no load speed
---/min ..........revolutions or reciprocation per minute
In the following cases, clean the dust bag and fully remove
any dust.
Dust remaining in the dust bag may cause ignition.
● Sanding steel sheets after sanding materials such as
wood
● After completing sanding work
Do not throw sanding dust on an open fi re because
materials in fi ne particle form may be explosive:
30. Because the cordless power tool operates by battery
power, be aware of the fact that it can begin to operate
at any time.
31. When working at elevated locations, clear the area of
other people and aware of conditions below you.
32. Do not use the product if the tool or the battery
terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
33. Keep the tool's terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result
in smoke emission or ignition.
34. Always use the tool and battery at temperatures
between 23°F (-5°C) and 104°F (40°C).
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers.
To avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YFSL.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT
rechargeable battery models of the multi volt series
and the BSL18 series. Other models of batteries may
burst causing personal injury and damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fi re, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress.
English
5