Moteur Pneumatique Ancien Modèle (Pompe Révisions A-C) - Nordson PermaFlo 815 Manuel

D 1‐2 Pièces du moteur pneumatique
Moteur pneumatique ancien modèle
(pompe révisions A-C)
Pièce P/N
- ‐ ‐ ‐ ‐ ‐ ‐
1 ‐ ‐ ‐ ‐ ‐ ‐
2 ‐ ‐ ‐ ‐ ‐ ‐
3 ‐ ‐ ‐ ‐ ‐ ‐
4 ‐ ‐ ‐ ‐ ‐ ‐
5 983058
6 1021378
7 ‐ ‐ ‐ ‐ ‐ ‐
8 940180
9 940154
10 1021313
11 ‐ ‐ ‐ ‐ ‐ ‐
12 941080
13 941373
14 1023598
15 1021425
16 ‐ ‐ ‐ ‐ ‐ ‐
17 952101
18 1021442
19 ‐ ‐ ‐ ‐ ‐ ‐
20 ‐ ‐ ‐ ‐ ‐ ‐
21 1021440
22 1021428
23 1021441
24 ‐ ‐ ‐ ‐ ‐ ‐
25 1021635
26 942230
27 ‐ ‐ ‐ ‐ ‐ ‐
28 1021444
29 132154
30 240976
31 132054
32 ‐ ‐ ‐ ‐ ‐ ‐
33 ‐ ‐ ‐ ‐ ‐ ‐
34 ‐ ‐ ‐ ‐ ‐ ‐
35 1021508
36 ‐ ‐ ‐ ‐ ‐ ‐
NOTE A: Les pièces ainsi notées sont comprises dans le kit valve pilote, P/N 1030558.
B: Les pièces ainsi notées sont comprises dans le kit coupleur, P/N 1024892.
C: Valve pneumatique nouveau modèle (Figure D 1‐4) utilisée sur les pompes révisions D et ultérieures.
D: Les silencieux nouveau modèle (Figure D 1‐2) remplacent les anciens silencieux de forme incurvée.
P/N 397921G02
Voir la figure D 1‐1.
Description
AIR MOTOR, 8‐inch, assembly
S SCREW, hex, cap,
5
/ -11 x 9.50 in., steel, clear zinc
8
S HEAD, cylinder, upper, 8‐inch
S BOLT, eye,
3
/ -16 x 0.750 in. shank, steel
8
S SCREW, hex washer head, 10‐32 x 0.375, stainless
steel
S WASHER, flat, 0.219 x 0.50 x 0.049 in., stainless
steel
S ACTUATOR, cartridge, assembly
S S CAP/PLUG, SH38, 3/8‐in socket
S S O‐RING, hot paint, 0.75 x 0.875 x 0.063 in.
S S O‐RING, Buna‐N, 0.563 x 0.688 x 0.063 in.
S VALVE, 3‐way, cartridge, assembly
S S O‐RING, hot paint, 0.813 x 0.938 x 0.063 in.
S O‐RING, Buna‐N, 0.250 x 0.438 x 0.094 in.
S O‐RING, Viton, black, 2.063 x 2.250 in.
S O‐RING, Buna‐N, 7.734 x 8.012 x 0.139 in. (‐265)
S CYLINDER, air, 8‐inch
S HEAD, cylinder, lower, 8‐inch
S CUP, U, polyurethane, 1‐
S PLATE, back‐up
S SCREW, socket,
1
/ -20 x 0.50 in., cap
4
S NUT, hex, flanged serrated,
S ROD, connecting, piston
S PISTON, air, 8‐inch, carboxylated nitrile
S WASHER, 0.380 x 2.00 x 0.060 in., stainless steel
S SCREW, low head, socket,
S VALVE, air, 4‐way, 7‐port, 2‐position
S O‐RING, hotpaint, 1.625 x 1.875 x 0.125 in.
S WASHER, lock, split, 0.25 in., stainless steel
S MUFFLER, PermaFlo
STUD, ground
CLAMP, ground, with wire
RETAINER, wire
SCREW, socket set, 0.375-24 x 0.250 in., cup point,
stainless steel
COUPLING, shaft, retainer sleeve
COUPLING, shaft
STUD, air motor, PermaFlo
NUT, hex, flanged serrated,
3 11 5
/ x 1‐ / x / in.
16 16 16
5
/ in., clear zinc
8
3
/ ‐16 x 1.00, zinc, nylok
8
5
/ in., clear zinc
8
Quantité Note
1
4
1
1
4
4
2 A
1 A
1 A
1 A
2 A
4 A
4
2
2
1
1
1
1
8
4
1
1
1
1
1 C
4
8
2 D
1
1
1
2 B
1 B
2 B
3
3
E 2007 Nordson Corporation