Klipsch Gallery Serie Mode D'emploi page 4

SPEAKER/SOUNDBAR ON-WALL INSTALLATION
If you mount your G-12,G-16,G-28 speakers or G-42 soundbar on a wall, do
not attach the pedestals. Determine a suitable location for each speaker to
wall-mount and complete all wiring to all speaker positions before mounting
speakers to the wall. Do not ceiling-mount.
1. If you have the G-28 or G-42, use included template and choose mount
position for the speaker (horizontal or vertical). Pin template to wall, mak-
ing sure it is level (when horizontally mounting) or plumb (when vertically
mounting) and positioned correctly, centered with the TV's center points for
example. Mark on wall the pilot hole locations through the template and
remove template. If you have the G-12 or G-16, mark on wall 2 pilot hole
points 9.26"apart for the G-12 or 13.25"apart for the G-16 (make sure
the points are lined up so that the speaker hangs straight up and down verti-
cally or level horizontally). For all speakers, Leave a minimum of one inch
space between speaker cabinet and TV. Keep in mind that, when mounted,
the speaker will "lock" into position 5/16" lower than where the pilot holes
are drilled.
2. Pre-drill pilot holes in marked locations. If drilling into a wall stud (ideal) it is
recommended to use #10 mounting screws (not included) to mount the
speaker bracket (G-28 and G-42) or the speaker itself (G-12 and G-16).
If there is no stud where a pilot hole is located, install wall anchors (not
included) into the pilot holes to hold the bracket or speaker instead. Wall
anchors should be rated to at least 6 pounds (G-12 and G-16) or 12 pounds
(G-28 and G-42).
If vertical wall-mounting, feed speaker wire into speaker bottom area
3.
and attach each wire to appropriate screw-terminal binding post (See
Diagram 2). If horizontal wall-mounting, feed speaker wire to channel(s)
that start on the back center part of the speaker, then continue run-
ning wire through the channel(s) and attach each wire to the appropri-
ate screw-terminal binding post the same as if vertical mounting. (See
Diagram 3) (Note: using speaker wire larger than 18 gauge may
not allow wire(s) to completely fit in channels). If needed, stick the
included adhesive strip on a point over the channel to hold the wires
in place in the channel. To change the Klipsch logo direction on the
speaker front gently pull out one side of it and rotate 45˚.
4. Gently push the speaker onto the two tabs on the mounted bracket through
its keyholes (G-28 and G-42) or onto the two screws in the wall (G-12 and
G-16) and push 5/16" down to lock into position.
CONNECTING
G-12,G-16,G-28 Connection - Using 16-gauge or larger speaker wire, con-
nect the RED "positive" (+) terminal of the LEFT speaker to the RED "positive"
(+) terminal of your amplifier's LEFT channel. Connect the BLACK "negative" (-)
terminal of the left speaker to the BLACK "negative" (-) terminal of your amplifier's
left channel. Repeat this procedure for connecting all remaining speakers to the
appropriate amplifier channels.
G-42 soundbar Connection - Since this speaker contains the LEFT, RIGHT and
CENTER channels, connect each one of these channels from your amplifier as
above to the designated "Left", "Right" and "Center" terminals on the G-42.
Make sure that no bare wires from any of the connections touch each other or
any other terminals as this could cause a short and damage your equipment.
SPEAKER CARE AND CLEANING
Your Klipsch Gallery™ Speaker has a durable finish that should only require dry
dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based
cleaners and harsh detergents. The unique grille for the speaker consists of a
piece of sheer rectangular cloth with metal rods along two sides. It is held in
place by magnets imbedded in a slot on each side of the rear of the cabinet.
Carefully pull the metal rod away from one side, then the other to remove
grill. The grill is designed to be as lightweight and acoustically transparent as
possible so there is no rigid framework behind it. Because of this, it might be
necessary to "smooth" the cloth once the grill is attached to the cabinet by us-
ing two thumbs to pull the cloth taught from top to bottom (or side to side if unit
is mounted horizontally).
DIAGRAM 1
Sub Pre Out
Monitor
Out
Video
In Out In In In In
L L
R R
CD TAPE TV DVD CBL/SAT
DIAGRAM 2
DIAGRAM 3
HDMI Out HDMI 1 HDMI 2 HDMI 3
Front Right Front Left Center Surround Surround Back Surround Back Surround
Right Left Right Left
Speaker Hookup