Maintenance & Care; After Cleaning; Machine Storage - Bissell LITTLE GREEN PROHEAT 1425 Serie Mode D'emploi

Operations
4. Apply downward pressure on the tool and pull
it toward you. The suction will remove the dirt
and cleaning solution. Continue until no more
dirt can be removed.
NOTE: If using the TurboBrush® Tool, move
the switch to the "SUCTION" position. This
activates the suction to remove the dirt
and cleaning solution. Move the switch
back to the "BRUSH" position for additional
brushing action.
5. As a final step, use "drying strokes" (by not
pressing the spray trigger) to remove as much
liquid/moisture as possible. Repeat this step as
often as necessary.
NOTE: If using the TurboBrush® Tool, move
the switch to the "SUCTION" position. This
activates the suction to remove the dirt and
cleaning solution.
Maintenance & Care

After Cleaning

1. Turn power switch to OFF position.
2. Unplug power cord from outlet.
NOTE: If a significant amount of Little Green
formula/water remains, it is all right to leave it
in the clean water/solution tank for your next
cleaning task.
3. Empty and rinse the dirty/collection tank after
each use, OR when dirty water reaches the
indicated maximum fill line. To remove the tank,
lift up the dirty/collection Tank retainer lever and
remove the tank from the unit.
4. Disconnect the cleaning tool from the spray
trigger by pushing down on button lock and
pulling straight off (DO NOT twist tools to
remove them).
5. Once removed from the spray trigger, all tools
can be cleaned by rinsing under clean running
water. The TurboBrush tool's switch must be in
"SUCTION" position before rinsing under clean
running water.
6. Check spray nozzle for accumulated dirt or
debris. If necessary, clean with soft bristle brush.

Machine storage

1. Wipe all surfaces with a soft cloth.
2. Wrap power cord around the cord wrap on
the back of the Little Green PROheat.
3. Wrap flex hose around the base of the unit
and secure the spray trigger.
4. Store unit in protected, dry area, at room
temperature (40º to 110ºF).
www.BISSELL.com 800.237.7691
8
WARNING
To reduce the risk of electric shock, turn power switch
off and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Retainer Lever
3.
Troubleshooting
Problem Possible causes
Spray nozzle clogged
Clean water/solution tank empty
Clean water/solution tank insert
Reduced
clogged
spray or
no spray
Pump needs priming
Tank release latch is not closed
properly
Poor tool position
Deep cleaner
Dirty water/collection tank is full
won't pick
up cleaning
Tool brush worn
solution
Excess solution in vacuum flex
hose
Incorrect Cleaning Formula
TurboBrush®
Incorrect switch position on
Tool: brush
TurboBrush
will not turn
TurboBrush® Incorrect switch position on
Tool: no TurboBrush
suction
Other maintenance or service not included in the manual should
Please do
be performed by an authorized service representative.
not return
Thank you for selecting a BISSELL product.
this product
For any questions or concerns, BISSELL is happy to
to the store.
be of service. Contact us directly at 1-800-237-7691.
WARNING
To reduce the risk of electric shock, turn power switch
off and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Remedies
Clean spray nozzle
Check/refill tank
Clean insert at bottom of clean water/
solution tank
Gently lift clean water/solution tank
while depressing the spray trigger
OR gently squeeze clean tank while
depressing spray trigger
Lift up the tank release latch and press
down firmly to make sure it is in place
Reposition tool on surface, follow
recommended cleaning procedures
Empty dirty water/collection tank
Replace with new brush
Lift tool and point upwards to allow
water in hose to flow into the dirty
water/collection tank
Use BISSELL 2X compact formulas only
Reposition switch to brush position
Reposition switch to suction position
www.BISSELL.com 800.237.7691
9