Important Charging Notes - Black & Decker CD182 Mode D'emploi

All manuals and user guides at all-guides.com
90504616 CD182 manual 5/31/06

IMPORTANT CHARGING NOTES

1. After normal usage, your battery pack should be fully charged in 3 to 9 hours. If the
battery pack is run-down completely, it may take up to 9 hours to become fully
charged. Your battery pack was sent from the factory in an uncharged condition.
Before attempting to use it, it must be charged for at least 9 hours.
2. DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above
105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack.
Longest life and best performance can be obtained if battery pack is charged when
air temperature is about 75°F.(24°C).
3. While charging, the charger may hum and become warm to touch. This is a normal
condition and does not indicate a problem.
4. If the battery pack does not charge properly—(1) Check current at receptacle by
plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to
a light switch which turns power off when you turn out the lights. (3) Move charger
and battery pack to a surrounding air temperature of 40°F (4,5 °C) to 105°F.(40,5 °C)
(4) If the receptacle and temperature are OK, and you do not get proper charging,
take or send the battery pack and charger to your local Black & Decker service
center. See Tools Electric in yellow pages.
5. The battery pack should be recharged when it fails to produce sufficient power on
jobs which were easily done previously. DO NOT CONTINUE using product with its
battery pack in a depleted condition.
6. To prolong battery life, avoid leaving the battery pack on charge for extended periods of
time (over 30 days without use). Although overcharging is not a safety concern, it can
significantly reduce overall battery life.
7. The battery pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before
recharging. Normal usage is the best method of discharging and recharging the
batteries.
SAFETY WARNINGS AND INSTRUCTIONS: DRILLS
1. Hold drill firmly with one hand on the grip and the other hand on the bottom of the
battery pack.
2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.
WARNING: Drill may stall (if overloaded or improperly used) causing a twist. Always
expect the stall. Grip the drill firmly to control the twisting action and prevent loss of
control which could cause personal injury. If a stall does occur, release the trigger
immediately and determine the reason for the stall before re-starting.
OPERATING INSTRUCTIONS
TRIGGER SWITCH & REVERSING BUTTON (FIGURE D)
• The drill is turned ON and OFF by pulling and releasing the trigger switch (1). The
farther the trigger is depressed, the higher the speed of the drill.
• A forward/reverse control button (2) determines the direction of the tool and also
serves as a lock off button.
• To select forward rotation, release the trigger switch and depress the forward/reverse
control button.
• To select reverse, depress the forward/reverse control button the opposite direction.
NOTE: The center position of the control button locks the tool in the off position.
When changing the position of the control button, be sure the trigger is released.
TORQUE CONTROL (FIGURE E)
This tool is fitted with a collar (3) to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece materials require a higher torque
setting than small screws and soft workpiece materials.
• For drilling in wood, metal and plastics, set the collar to the drilling position symbol
• For screwdriving, set the collar to the desired setting. If you do not yet know the
appropriate setting, proceed as follows:
• Set the collar to the lowest torque setting.
• Tighten the first screw.
1:21 PM Page 7
7
.