Insignia IS-LCDTV32 Guide De L'utilisateur page 7

All manuals and user guides at all-guides.com
IN-LCDTV-32.book Page 3 Friday, May 13, 2005 4:15 PM
IS-LCDTV32 32-inch Color TV
NEC-NATIONAL ELECTRICAL CODE
• If an outside antenna is connected to the television
equipment, be sure the antenna system is grounded
so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the
National Electrical Code provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements
for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
1 Electric service equipment
2 Power service grounding
electrode system (NEC art
6
250, part H)
3 Ground clamps
4 Grounding connectors
(NEC Section 810-21)
5
5 Antenna discharge unit
(NEC Section 810-21)
4
6 Antenna lead in wire
3
1
2
NEC—NATIONAL ELECTRICAL CODE
• An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can collide with such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching such power lines or circuits, as
contact with them might be fatal.
Preparations
Using the Remote Control
Note: This
illustration is for
reference only. The
remote sensor may
be in different
locations on
different models.
• Use the remote control by pointing it towards
the remote sensor window of the set. Objects
between the remote control and sensor
window may prevent proper operation.
Caution
• Do not expose the remote control to shock.
In addition, do not expose the remote
control to liquids, and do not place in an
area with high humidity.
• Do not install or place the remote control
under direct sunlight. The heat may cause
deformation of the unit.
• The remote control may not work properly if
the remote sensor window of the main unit
is under direct sunlight or strong lighting. In
such a case, change the angle of the
lighting or LCD TV set, or operate the
remote control closer to the remote sensor
window.
Batteries for the Remote Control
If the remote control fails to operate the LCD TV
functions, replace the batteries in the remote.
(Place the batteries with their
terminals corresponding to the (+)
and (-) indications in the battery
compartment.)
1 Open the battery cover.
2 Insert two size-AAA batteries.
3 Replace the cover.
Caution Precaution on battery use
• Improper use of batteries can result in a
leakage of chemicals and/or explosion. Be
sure to follow the instructions below.
• Place batteries with their terminals
corresponding to the (+) and (-) indications.
• Different types of batteries have different
characteristics. Do not mix batteries of
different types.
• Do not mix old and new batteries. Mixing
old and new batteries can shorten the life of
new batteries and/or cause old batteries to
leak chemicals.
• Remove batteries as soon as they are
non-operable. Chemicals that leak from
batteries can cause a rash. If chemical
leakage is found, wipe with a cloth.
• The batteries supplied with the product may
have a shorter life expectancy due to
storage conditions.
• If the remote control is not used for an
extended period of time, remove the
batteries from the remote control.
Power Connection
1 Connecting the female plug to the AC socket
on the unit.
2 Connecting the male plug to the wall outlet as
illustrated.
Note
• This illustration is for reference only. The
AC plug may be different on different
models.
• This product should be operated only from
the type of power source indicated on the
marking label.
• Always unplug the AC cord from power
outlet when not using for a long period of
time.
www.insignia-products.com
3