Putting Into Operation; Transporting The Appliance; Installing The Appliance; Disposing Of Packaging - Atag KD8178CD Mode D'emploi

4 Putting into operation

4.1 Transporting the appliance

CAUTION
Risk of injury and danger of damage as a result of incorrect
transport!
u Transport the appliance in a packed condition.
u Transport the appliance upright.
u Do not transport the appliance without assistance.

4.2 Installing the appliance

In the event that the appliance is damaged, contact the supplier
immediately before connecting to the mains.
The floor at the site must be flat and level.
Do not install the appliance in a location where it is exposed to
direct radiation of the sun, next to a cooker, heater and similar.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m
refrigerant used in the appliance. If the room in which the appli-
ance is installed is too small, a flammable gas-air mixture may
form in the event of a leakage in the refrigeration circuit. The
quantity of refrigerant used in your appliance is indicated on the
type plate on the inside of the appliance.
Fit the appliance in stable kitchen units only.
The following ventilation gaps must be observed:
The depth of the ventilation channel at the rear of the unit
q
must be at least 38 mm.
There must be a ventilation space of at least 200 cm
q
plinth and at the top of the unit.
Basically the principle applies: the larger the ventilation
q
space, the more energy-saving the appliance is in operation.
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
u The appliance is designed for use in enclosed areas. Do not
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
WARNING
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flam-
mable. Escaping refrigerant may ignite.
u Do not damage the piping of the refrigeration circuit.
WARNING
Fire hazard and danger of damage!
u Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
u Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
After installation:
u Remove all transit supports.
All manuals and user guides at all-guides.com
u Unscrew the red transport
lock.
retaining
stopper (60).
u Dispose of packaging material (see 4.3) .
Note
u Clean the appliance (see 6.2) .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u Always see to good ventilation at the installation site.

4.3 Disposing of packaging

Danger of suffocation due to packing material and plastic film!
u Do not allow children to play with packing material.
The packaging is made of recyclable materials:
2 per 8 g of R 600a
- corrugated board/cardboard
- expanded polystyrene parts
- polythene bags and sheets
- polypropylene straps
- nailed wooden frame with polyethylene panel*
u Take the packaging material to an official collecting point.

4.4 Connecting the appliance

in the
2
NOTICE
Risk of damage to the electronic control system!
u Do not use stand-alone inverters (conversion of d.c. to a.c./
three-phase) or energy saving plugs.
Fire and overheating hazard!
u Do not use extension cables or multiple socket outlets.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
Connect the appliance only with a properly installed
socket outlet with earthing contact. The socket outlet
must be fused with 10 A or higher.
It must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emer-
gency. It must be outside the area of the rear of the
appliance.
u Check the electrical connection.
u Plug in the power plug.

4.5 Switching on the appliance

Put the appliance into operation about 2 hours before first
loading food to be frozen.
Do not load food to be frozen before the temperature display
reads -18 °C.
u Press On/Off button
w The temperature display flashes until the temperature is
sufficiently cold. If the temperature is above 0 °C, dashes
flash. If it is below, the set temperature flashes.
Putting into operation
Close the vacated
hole using the
WARNING
WARNING
Fig. 2 (4) .
19