Additional Safety Warnings - Scheppach CCS165-20Li Traduction Des Instructions D'origine

ways wear safety glasses. The wearing of per-
sonal protective equipment such as dust masks,
non-slip safety shoes, safety helmets or ear pro-
tectors, appropriate to the type of electrical power
tool used and work undertaken, reduces the risk
of injury.
c. Avoid unintentional operation of the de-
vice. Check that the electrical power tool
is switched off before you connect it to the
mains, pick it up or carry it. Accidents can hap-
pen if you carry the device with your finger on the
ON / OFF switch or with the device switched on.
d. Remove any setting tools or spanners before
you switch the device on. A tool or spanner left
attached to a rotating part of a device can lead to
injury.
e. Avoid placing your body in an unnatural po-
sition. Keep proper footing and balance at all
times. By doing this you will be in a better position
to control the device in unforeseen circumstanc-
es.
f. Wear suitable clothing. Do not wear loose
clothing or jewellery. Keep your hair, clothing
and gloves clear of moving parts. Loose cloth-
ing, jewellery or long hair can become trapped in
moving parts.
g. If vacuum dust extraction and collection de-
vices are fitted do not forget to check that
they are properly connected and correctly
used. The use of these devices reduces the haz-
ard presented by dust.
4. Careful handling and use of electrical power
tools
a. Do not overload the device. Always use an
electrical power tool that is intended for the
task you are undertaking. By using the right
electrical power tool for the job you will work more
safely and achieve a better result.
b. Do not use an electrical power tool if its switch
is defective. An electrical power tool that can no
longer be switched on and off is dangerous and
must be repaired.
c. Pull the mains plug from the socket before you
make any adjustments to the device, change
accessories or when the device is put away.
This precaution is intended to prevent you from
unintentionally starting the device.
d. When not in use always ensure that electrical
power tools are kept out of reach of children.
Do not let anyone use the device if he or she
is not familiar with it or has not read the in-
structions and advice. Electrical power tools
are dangerous when they are used by inexperi-
enced people.
e. Look after the device carefully. Check that
moving parts are working properly and move
freely. Check for any parts that are broken
22 | GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
All manuals and user guides at all-guides.com
or damaged enough to detrimentally affect
the functioning of the device. Have damaged
parts repaired before you use the device.
Many accidents have their origins in poorly main-
tained electrical power tools.
f. Keep cutting tools clean and sharp. Carefully
maintained cutting tools with sharp cutting edges
are less likely to jam and are easier to control.
g. Use the electrical power tool, accessories,
inserted tools etc. in accordance with these
instructions and advice, and the stipulations
drawn up for this particular type of device. In
doing this, take into account the working con-
ditions and the task in hand. The use of elec-
trical power tools for purposes other than those
intended can lead to dangerous situations.

8. Additional Safety Warnings

Safety advice relating specifically to this device
Ensure that the device is always used in accordance
with the advice in these operating instructions and
only by persons over 16 years of age.
Note: Do not use grinding discs. Failure to observe
this advice may result in injury or damage. To avoid
danger to life from electric shock:
• Frequently check the condition of the device, mains
lead and plug. Do not use the device if these kinds
of parts are damaged. Never open up the device.
A damaged device, mains lead or plug presents a
serious danger to life from electric shock. Always
have any repairs carried out or replacement parts
fitted at the service centre or by an electrical equip-
ment repair specialist.
• Do not operate the device if it is damp and do not
use it in a damp environment.
• If you use the device outdoors, always connect
it through a residual current device (RCD) with a
maximum trip current of 30 mA. If using an exten-
sion lead, always use one that is approved for out-
door use.
Note: Always keep the mains lead away from the
working area of the machine and lead away the mains
lead from the rear.
CAUTION! To avoid the risk of injury:
a. Keep your hands away from the area around
the saw and clear of the saw blade. Hold the
auxiliary handle or the motor housing with
your free hand. If you have both hands on the
saw they cannot be injured by the saw blade.
b. Do not grip the underside of the workpiece.
The blade guard cannot protect you from the saw
blade under the workpiece.
c. Set the cutting depth to match the thickness