Lincoln PowerLuber 1880 Mode D'emploi page 4

The gun uses lubricants, that may be flam-
mable and poisonous if ingested. Do not use
gun near open flame or other fire hazards.
Greases are often marketed as high tem-
perature because it must maintain their lu-
bricating properties in hot areas, but the lu-
bricants may be flammable if the
temperature is too high. Please read all
warnings on lubricants before using this
gun. Do not use flammable greases with this
grease gun.
Tool use and care
Do not use tool if switch does not turn it on
or off. A tool that cannot be controlled with
the switch is dangerous and must be
repaired.
Do not continue to hold down trigger if
grease gun is stalled. This could damage the
motor or cause fire.
Disconnect battery pack from tool before
making any adjustments, changing acces-
sories, or storing the tool. Such preventive
safety measures reduce the risk of starting
the tool accidentally.
Store the tools out of reach of children
and other untrained persons. Tools are dan-
gerous in the hands of untrained users.
When battery pack is not in use, keep it
away from other metal objects like: paper
clips, coins, keys, nails, screws, or other
small metal objects that can make a con-
nection from one terminal to another.
Shorting the battery terminals together may
cause sparks, burns, or a fire.
Maintain tools with care. Check for mis-
alignment or binding of moving parts,
breakage of parts, and any other condition
that may affect the tool's operation. If dam-
aged, have the tool serviced before using.
Many accidents are caused by poorly main-
tained tools.
Use only accessories that are recom-
mended by Lincoln.
Only accessories that are capable of han-
dling 10,000 psi (689 bar) should be used.
Accessories that may be suitable for one tool
may create a risk of injury when used on
another tool.
Appropriate use
The PowerLuber was exclusively designed to
pump and dispense lubricant using 18 volt
battery power. Do not exceed the maximum
specification ratings.
4
Specifications
Basic PowerLuber model 1880
Operating power 14.5 to 20.5 V DC
Maximum operating
pressure
Low output 6,000 psi (413 bar)
High output 6,000 psi (413 bar)
Grease reservoir 14.5 oz. (411 g)
capacity
Maximum peak 10,000 psi (689 bar)
pressure
Operating temperature 0 to 120 °F
range (–18 to 50 °C)
Operating current 4 A at 20 to 130 °F
(–6 to 54 °C)
Rated current 5 A at 20 to 130 °F
(–6 to 54 °C)
Lubricant (grease) up to NLGI #2
Grease output
Low output (L) 3.5 oz./min.
(0,103 l/min.)
High output (H) 5.5 oz./min.
(0,162 l/min.)
Weight 6.5 lbs. (2,0 kg)
Accessories
Battery li-ion Model 1871
Output 20 V DC maximum
Capacity 1,500 mAh
Battery charger Model 1870
Charge time 1.5 hours
Input, vac (0.6 A) 120 v, 60 hz
Outlet hose Model 1236
Pressure rating 10,000 psi (689 bar)
Length of the hose 36 in. (914 mm)
note 1: Operating current and grease output data at
1,000 psi (69 bar).
note 2: The declared vibration total value has been meas-
ured in accordance with a standard test method and may be
used for comparing one tool with another and the declared
vibration total value may also be used in a preliminary as-
sessment of exposure.
note 3: The vibration emission during actual use of the
power tool can differ from the declared total value depending
on the ways in which the tool is used; and of the need to
identify safety measures to protect the operator that are
based on an estimation of exposure in the actual conditions
of use (taking account of all parts of the operating cycle such
as the times when the tool is switched off and when it is run-
ning idle in addition to the trigger time).