Using The Remote To Control Your Components; On-Screen Menus; Accessing And Selecting Menu Items; Exiting A Menu Mode - RCA RCR430S Mode D'emploi

5. Starting with the number 1 key, press and release each
number key on the keypad in the following order (1-9, then
0). The number that causes the LED INDICATOR to blink
is the first number of the code. As you find each number
of the code, refer to the code boxes below and write them
down for future reference.
All TV codes begin with the number 1; all VCR codes
Note:
begin with the number 2; all DVDs, the number 3; and all
satellite receivers and cable boxes, the number 5.
6. Repeat step 5 until you have retrieved all four numbers in
the code.
7. After the fourth number is retrieved, the LED INDICATOR
blinks briefly, then turns off.
8. To exit the Code Retrieval Mode, press and release the GO
BACK key at any time.
9. If you press an invalid key during the Code Retrieval
process, the remote will not respond. If you do not press
a valid Code Retrieval key (TV, DVD•VCR, SAT•CBL,
AUX, INFO, GO BACK), Code Retrieval times out after 15
seconds. The LED INDICATOR blinks four times, and then
turns off.
TV CODE
1
VCR CODE
·
SAT CBL CODE
5
Using the Remote to
Control Your Components
Because this remote controls more than one component, you
must first "tell" the remote which component you wish to
operate. That means, if you wish to operate your TV, you
must first press the TV key to put the remote in the TV Mode.
The remote stays in the chosen component mode (such as TV
Mode) until you change it. If your remote is in TV Mode, you
must change the mode in order to operate your DVD or VCR,
satellite receiver or cable box. For example, if you are in VCR
Mode, and you wish to turn off your TV, you must press the
TV key first before pressing the ON•OFF key.

On-screen Menus

Accessing and Selecting Menu Items

Today's advanced components use on-screen menus to
help you navigate through all their features and functions.
While this remote cannot access every menu system of every
component model, it does offer some menu functionality.
To use a component's on-screen menu system, you first have
to put the remote in Menu Mode.
1. Make sure your components are turned on and your TV
is set to the component's input. (Use the INPUT key to
toggle through video sources when in TV mode.)
2. Press the component key whose menu you want to access.
3. Press the MENU key. The LED INDICATOR blinks, indicating
you are in the Menu Mode.
10
DVD CODE
AUX
TV VCR DVD SAT·CBL
4. Use the VOL+/- and/or CH+/- keys to navigate through the
on-screen menu system.
5. To make a selection from the on-screen menu, press
the MENU or OK key to select the highlighted item.
If the remote doesn't respond, check to see that the
!
TIP:
LED INDICATOR is still blinking. Note: it times out after 20
seconds. If this happens, just press the MENU key again, and
then retry your selection.

Exiting a Menu Mode

The remote automatically times out of Menu Mode after
20-seconds of inactivity (no keys being pressed). At that
time, the remote clears the displayed menu from the TV.
If you want to exit the Menu Mode yourself, press the
corresponding component key on the remote (TV, DVD•VCR,
SAT•CBL). The LED INDICATOR turns off.
Sleep Timer (Select Models Only)
This feature automatically turns off your TV at a duration
you choose from 1 to 99 minutes. The Sleep Timer only works
if you have found a code that controls your TV. The timing
mechanism for the Sleep Timer is built into your universal
remote control. To program the Sleep Timer, follow these steps.

Programming the Sleep Timer

1. Press and release the TV key.
2. Press and hold the SLEEP key for three seconds. The LED
INDICATOR turns on.
3. Release the SLEEP key.
4. Using the number keys, enter the desired time in minutes
(from 1-99 minutes). To set the timer to a number under 10
minutes, first press 0 and then the desired number (e.g.,
05 for five minutes). The LED INDICATOR blinks with
each keypress.
5. Once the second number is entered, the LED INDICATOR
turns off.
Any keypress other than the number keys is ignored.
!
TIP:
If you don't enter the sleep time within 10 seconds after
pressing the SLEEP key, you must start over at step 1. The
LED INDICATOR blinks four times and then turns off,
indicating your attempt to program the Sleep Timer has been
unsuccessful.
6. The Sleep Timer is now set.
7. Leave remote aimed at the TV. Once the Sleep Timer is set,
you can continue to use the remote without affecting the
Sleep Timer. However, because the timing mechanism for
the Sleep Timer is built into the remote itself, the remote
must be in TV Mode and pointed at the TV to activate the

Sleep Timer.

Canceling the Sleep Timer

The Sleep Timer program will be canceled and reset to zero by
pressing and releasing the ON•OFF key.
11