Declaration of conformity
Güde GmbH & Co. KG Birkichstraße 6, 74549
Wolpertshausen, Germany declares herewith, that
design and construction of further mentioned devices,
that we put on market, conforms with relevant EU
standards and its basic requirements for health and
safety.
In case of modification of the device which was
not consulted with our company, this declaration
is not applicable.
Device mark: GRW 1800
Product number: 58048
Date/Manufacturer signature: 12.03.09
Signed by: Mr. Arnold, managing director
ES relevant standards:
Directive 98/37/ES - Machine equipment
Low Voltage Electrical Equipment Directive
73/23/EHS; 87/404/EHS
Directive No. 2004/108/EC on electromagnetic
compatibility, including changes
Directive ES 93/68/EHS,
Directive ES 2000/14 EHS
Noise level data see Technical data
Used harmonized standards:
EN 61000-3-2:2006, EN 61000-3-3/A2:2005
EN 55014-1:2006, EN 55014-2/A2:2005
EN 60745-1-2:2003
Certification authority: TÜV Product Service
GmbH, TÜV SÜD Gruppe, Riedlerstraße 65, 80339
München, Germany
Machine description
1. Starting switch with safety function (pict. 6/1)
2. Rotary switch for two-stage gearbox (pict. 5/2)
3. Rotary button for fine revolution adjustment
(pict. 4/3)
4. Agitator (pict. 2 and 3)
Warranty
Warranty claims see warranty card enclosed.
General safety instructions
Do not operate the machine in explosive environment.
Do not mix solvents neither substances containing
solvents, with ignition point lower than 21°C
Do not wind the cord around body parts
Use only extension cables approved for use on your
work place.
Start and stop the machine inside the mixing tank.
Ensure that the mixing tank is stable. Hands and
foreign objects should be kept away from the mixing
tank when the mixer is in operation. We recommend
wearing safety gloves and safety goggles when
operating the mixer.
Wear skin tight overall.
While running the machine take always into
account sudden strong torque.
PLEASE OBSERVE FOLLOWING SAFETY
INSTRUCTIONS TO ENSURE HIGH LEVEL OF
SAFETY:
Warning: Operate with RCD only
(residual current device)!
WARNING!
Keep your workplace clean and tidy.
Messy workplace or table increases the risk
of accident and injury.
Pay attention to your working
environment. Electric devices and tools
shall not be used in damp or humid
environment. Do not expose the electric
devices to rain or humid air.
Do not let unauthorized persons to come
close to the machine. Keep observers and
visitors, especially children and older people,
away from your workplace.
Store your tools safely.
Tools you are not using must be stored on
dry, elevated or inaccessible place.
Use always job specific tools. Never use
e.g. light tools or accessories for job which
requires heavy tools. Use only tool designed
for specific job. Keep your tools clean and in
a safe operating condition at all times.
Wear proper attire. Avoid loose clothing and
jewellery. It could be caught by moving
machine parts. Use working gloves while
working outdoors. Protect your long hair
carefully.
Use Personal Protective Equipment.
If the noise level exceeds 85dB (A), wear ear
protection!
To protect your breathing against dust, wear
a mask with dust filter.
Watch out for cord. Do not pull the cord.
When disconnecting the cord pull the plug.
Keep the cord away from heat, oil and sharp
edges.
Always pay attention to your stability and
footing. Do not overreach when working with
the mixer.
Avoid accidental start up. Always ensure
that the starting switch is in off position
before plugging the cord in the socket.
Use special extension cables while
working outdoors. While working outdoors
you will need special extension cables
bearing corresponding marking.
Keep your attention. Always pay attention
to what you are doing. Use common sense.
Do not use electric devices when tired.
Watch out for damaged parts. Check the
tools before use. Are there any parts
damaged? In case of minor defects consider
if the tool will work fine and safely. Make sure
that all moving parts are aligned properly. Do
4
GB