Installation, Cleaning And Replacement Of The Separator (Optional); Tightness Inspection; Disposal; Wiring Diagrams - Nilfisk T40PLUS Manuel D'instructions

Installation, cleaning and replacement of
the separator (optional)
Figure 21
[ NOTE ]
Instructions describing how to fit the optional kits and the
relative operation and maintenance manuals are supplied
together with the optional kits.
CAUTION!
The projection screw (5) positioned on the filter holder
ring supplied with the kit must be removed; failure to
do this could cause the filter to break.
[ NOTE ]
If there is only a dust deposit on the separator (4) allow the
dust to drop through the central hole.
The separator (4) should first be disassembled in order to be
perfectly cleaned:
■ Release the closing hooks (1) of the cover (2) and remove
the cover.
■ Remove the filter.
■ Unscrew the two screws (3) and remove it from the
container.
■ Replace the part if it is excessively worn.
■ Reinstall the separator (4).
■ Lock it and fix it by means of the two screws (3).
■ Fit the filter back in place, close the cover (2) and lock it by
means of the two the closing hooks (1).

Tightness inspection

Hoses check
Figure 22
Make sure that connecting hoses (1) are in a good condition
and correctly fixed.
If the hoses are damaged, broken or badly connected to the
unions, they must be replaced.
When sticky materials are treated, check for possible clogging
along the hose, in the inlet and on the baffle plate inside the
filtering chamber.
To clean, scrape the inlet (2) from the outside to remove
deposits.
Filtering chamber gasket check for machines
equipped with dust container
Figure 23
If the gasket (1) between the container and the filtering chamber
(3) fails to guarantee tightness:
■ Loosen the four screws (2) that lock the filtering chamber
(3) against the machine structure.
■ Allow the filtering chamber (3) to lower down and tighten
the screws (2) once it has reached the tightness position.
If an optimal seal is not yet obtained or if there are tears, cracks,
etc., the gasket must be replaced.
Filtering chamber gasket check for machines
equipped with Longopac
Figure 24
Ensure that the Longopac® bag is tight with the gasket (2).
Also check the seal of the gasket positioned on the discharge
clapet (1).
system
®
The gasket must be replaced if it is torn, cut, etc...

Disposal

The crossed-out wheeled bin symbol on the equipment indicates
that used electrical and electronic equipment must be collected
and disposed of separately from household waste. The correct
disposal of the equipment will help prevent potential negative
consequences for the environment and human health.
Electrical and electronic household equipment must be
disposed of at the separate collection points in the residence
area. Please note that commercial electrical and electronic
equipment should be disposed of separately from the municipal
waste stream. We will be pleased to inform you about suitable
disposal options.

Wiring diagrams

Basic machine
Machine with cartridge filter and automatic cleaning
Code
Name
Z8 39111 + Z8 39113
H1
+ Z8 39114
Z8 39314 + Z8 39113
H3
+ Z8 39114
KM1 4083901550
PA Z8 39109 + Z8 39110
PM Z8 39107 + Z8 39108
4083901538
Q1
Z8 39924
4083901540
Q1
Z8 39924
SF1 Z8 391120
TR1 Z8 391051
4083901592
M1 4083901593
4083901603
Electric filter shaker (SE)
Code
Name
4083901794 +
H1 4083901811 +
4083901796
4083901799 +
H3 4083901811 +
4083901796
4083901550 +
KM1
4083901560
17
T40PLUS - T40WPLUS
Figure 25
Figure 26
Figure 27
Description
White lamp
Yellow lamp
Contactor kW 4
24VAC 1NO
Red button
Green button
5.5 - 8A main switch
9 - 12.5A main switch
Phase sequence relay
Transformer
63 VA 400-230/24V
Line terminal 4mmq S
Ground terminal 4mmq S
Fuse box terminal 15mmq
S
Figure 28
Description
White lamp
Yellow lamp
Contactor kW 4
24VAC 1NO
Q.ty
1
1
1
1
1
1
1
1
GB
1
3
2
4
Q.ty
1
1
1
C380