tau SPIN12 Manuel D'emploi Et D'entretien page 18

b 4x1,5 mm² + 3x0,5 mm²
c 2x0,5 mm² (TX)
d 4x0,5 mm² (RX)
e 2x0,5 mm²
f 2x1 mm² + 1RG58
g 3x0,5 mm²
h 3x0,5 mm²
i 4x1,5 mm²
The distance between the control unit and the motor must not exceed 10 - 12 m.
SPIN12 / SPIN12-B: use only M-030000CC50 cable or equivalent.
13. GUARANTEE: GENERAL CONDITIONS
TAU guarantees this product for a period of 24 months from the date of purchase (as proved by the sales document, receipt or invoice).
This guarantee covers the repair or replacement at TAU's expense (ex-works TAU: packing and transport at the customer's expense) of parts
that TAU recognises as being faulty as regards workmanship or materials.
For visits to the customer's facilities, also during the guarantee period, a "Call-out fee" will be charged for travelling expenses and labour costs.
The guarantee does not cover the following cases:
• If the fault was caused by an installation that was not performed according to the instructions provided by the company inside the
product pack.
• If original TAU spare parts were not used to install the product.
• If the damage was caused by an Act of God, tampering, overvoltage, incorrect power supply, improper repairs, incorrect installation,
or other reasons that do not depend on TAU.
• If a specialised maintenance man does not carry out routine maintenance operations according to the instructions provided by the
company inside the product pack.
• Wear of components.
The repair or replacement of pieces under guarantee does not extend the guarantee period.
In case of industrial, professional or similar use, this warranty is valid for 12 months.
Manufacturer:
Address:
Declares under its sole responsibility, that the product:
designed for automatic movement of:
for use in a:
complete with:
Model:
Type:
Serial number:
Commercial name:
Has been produced for incorporation on an access point (garage door) of for assembly with other devices used to move such an access point, to
constitute a machine in accordance with the Machinery Directive 2006/42/EC.
Also declares that this product complies with the essential safety requirements of the following EEC directives:
- 2014/35/EU Low Voltage Directive
and, where required, with the Directive:
Also declares that it is not permitted to start up the machine until the machine in which it is incorporated or of which it will be a component has been
identified with the relative declaration of conformity with the provisions of Directive 2006/42/EC.
The following standards and technical specifications are applied:
EN 61000-6-2; EN 61000-6-3;
103
The manufacturer undertakes to provide, on sufficiently motivated request by national authorities, all information pertinent to the quasi-machinery.
Sandrigo,02/11/2017
Name and address of person authorised to draw up all pertinent technical documentation:
Loris Virgilio Danieli - via E. Fermi, 43 - 3606 Sandrigo (Vi) Italia
2x2,5 mm² + 3x0,5 mm²
2x0,5 mm² (TX)
4x0,5 mm² (RX)
2x0,5 mm²
2x1 mm² + 1RG58
3x0,5 mm²
3x0,5 mm²
2x2,5 mm²
MANUFACTURER'S DECLARATION OF INCORPORATION
(in accordance with European Directive 2006/42/EC App. II.B)
- 2014/30/EU Electromagnetic Compatibility Directive
- 2014/53/EU Radio equipment and telecommunications terminal equipment
EN 60335-1; EN 300 220-2 V3.1.1;
_________________________________________
TAU S.r.l.
Via E. Fermi, 43 - 36066 Sandrigo (Vi) - ITALY
Electromechanical actuator
Garage doors
Residential environment
Electronic control unit and radioreceiver
SPIN
SPIN12 / SPIN12-B / SPINF / SPINQRE
SEE SILVER LABEL
AUTOMATION FOR GARAGE DOORS
EN 12453:2000;
Legal Representative
Loris Virgilio Danieli
18
EN 12445:2000; EN 60335-2-