Novellini X1 Notice D'installation, Utilisation Et Entretien page 60

If button 6 is a steady red, this means the level of disinfectant in the tank must be
topped up.
The disinfection cycle then starts. The pump starts up for about four minutes then stops.
After about 20 minutes, button 6 and the surround of button 2 stop flashing. Button 6
becomes a steady red indicating that the cycle has ended and the bath must be emptied.
In case of necessity, press button 5 to interrupt the disinfection cycle. Button 6 will
continue to flash in red until the panel goes off to indicate that disinfection has not
been completed.
When emptied, the bath is ready for use.
Cromolight:
When button 3 is pressed, it lights up in red, green or blue, activating a variable
programme, and the spotlight comes on.
Pressing button 3 a number of times obtains various programmes until the Cromolight
is turned off.
At the end of the available programmes, button 3 flashes to indicate the function is
about to go off.
To stop the function, hold button 3 down for a few seconds.
Emptying the Airpool system:
After the bath has been emptied, to ensure hygiene, the water remaining in the Airpool
jets must be eliminated. Baths with an Airpool function are therefore fitted with a
manual/automatic drain system.
When an Airpool or Whirlpool jet function has been activated, the system drains
automatically. After the bath has been emptied and about 30 minutes after the panel
goes off, the blower starts up for one minute to expel the residual water.
If a jet function has not been used, the system must be drained manually. After emptying
and with the bath in stand-by (panel backlit), press button 4 for a few seconds until the
blower starts up. After one minute it goes off automatically.
To disable all active functions with a single command, press button 5.
Pressing button 5 again turns the bath from stand-by to off.
It shuts down automatically if not used for 30 minutes.
ADJUSTING JET NOZZLES:
Turn the jet nozzles (C) as required. The nozzles can be turned in any direction. Make sure
that the nozzles are not clogged and are not directed upwards (otherwise water will be
splashed out of the tub when the system is switched on). Fill the tub until the water is
well over the level of the jet nozzles (see illustration). After getting into the bath, the
water level must be as shown in the illustration, otherwise the jets system may not
start. The system features a level sensor which prevents the jets from switching on if
there isn't enough water in the bath. When the jets system is on, do not use foaming
agents such as bubble baths, soap, etc.
HOW TO USE YOUR WHIRLPOOL BATH CORRECTLY:
The benefits of a whirlpool massage:
The swirling water of a whirlpool bath is naturally soothing and offers many therapeutic
benefits. In spas, hydrotherapy is used to stimulate blood circulation, relax muscles
and restore tone to the skin. Basically, it consists in injecting air into controlled jets of
water of varying intensity directed at the body. The jet of warm water and air bubbles
against the body dilates blood vessels and increases the flow of blood to the heart. In
addition, the continuous jet of water has a massaging effect on the muscles and dilates
skin pores, promoting the removal of toxins and helping to hydrate the surrounding
tissue. Hydromassage is widely used by sports people to relieve tired muscles after
strenuous physical activity, producing a pleasant sense of relaxation and well-being.
The jet nozzles can be adjusted to direct the jets at the parts of the body where you want
to concentrate the massaging action. The temperature of the bath water must never
exceed 45°C. The maximum benefits are obtained with a temperature of 36°-37°C.
CLEANING AND DISINFECTION:
Deposits of organic material that collect in the pipes during a whirpool bath promote
bacterial growth and, if left untreated, cause unsanitary conditions and unpleasant
odours. For perfect hygiene, the jets system should be disinfected immediately after
bathing, before draining. To disinfect, use 50 g of ordinary disinfectant (for example,
liquid bleach) for every 100 litres of water (approximately half a glass in a bath filled
to optimum level). Run the system for few minutes to circulate the disinfectant in the
pipes. Stop the system, allow to soak for 15/20 minutes, then drain the bath. If the bath
develops unpleasant odours after a long period of inactivity, it's a good idea to disinfect
the system before using it again. For hygiene, if the bath is used consecutively by two or
more people, the system should be disinfected after each use. During disinfection, turn
off the air control to reduce foaming.
MAINTENANCE AND CLEANING:
The bath is made of acrylic and must be cleaned using a liquid detergent and a soft cloth
or sponge. Use a good quality household liquid detergent. To prevent scale deposits,
wipe dry using a chammy leather or a soft lint-free cloth that removes stubborn
deposits without leaving traces. Limescale deposits may be removed using specific
detergent products. To restore shine to the acrylic surface polish with an ordinary wax
polish such as car wax.
DO NOT USE ABRASIVE CLEANERS, ALCOHOL OR ALCOHOL BASED PRODUCTS, ACETONE
OR OTHER SOLVENTS.
Warning: use of detergents other than those recommended may damage the bath
and/or the whirlpool equipment.
SURFACE SCRATCHES:
Small surface scratches can be removed using wet emery paper (grade 1000) and then
smoothing the surface with abrasive paste. Once the scratch has been removed, restore
surface shine using wax polish.
TROUBLESHOOTING:
In the event of a problem, perform the following checks before activating the warranty
or contacting qualified staff.
If the jet system does not start:
• If the circuit breaker has tripped, reset it and try switching on the jet system again.
• If the pump does not start when the water level is well above the nozzles.
• Check to ensure that the cut-out is turned on.
If the jet system does not stop:
• If the pump continues running and cannot be turned off using the usual controls, turn
it off using the circuit breaker and try again.
Do not make adjustments to the wiring or other electrical parts.
DISPOSING OF THE WHIRPOOL BATH:
For the disposal of the product or its parts, follow the local regulations on matters of
waste disposal. For Italy, Legislative Decree n. 152 of April 3, 2006 will hold, and for the
other EU countries, Directive 2008/98/EC.
PRODUCT GUARANTEE:
All products purchased by consumers, as defined in Article 3 of the Consumer Code
(Legislative Decree no. 206 of 6 September 2005 and subsequent amendments),
are covered by the legal guarantee of the seller under Article 128 and subsequent
amendments of the consumer Code. In case of lack of conformity of the product, we
invite the consumer to contact their dealer within the statutory deadline.
EC DECLARATION OF CONFORMITY:
The manufacturer Novellini S.p.a. Via Mantova, 1023 - 46030 Romanore di Borgo
Virgilio, Mantova - Italy Declares under its responsibility that the following products:
-60-
ENGLISH