SYNQ SMP16.42 Mode D'emploi page 11

ENGLISH
SPECIFICATIONS
Power Supply AC 230 V, 50Hz
Power consumption 40W
Max output level (0.5% thd @ 1kHz) +26dB (MAIN L/R) @ 10kOhm
+20dB (GROUP 1-2/3-4, AUX1, AUX2/EFX, CTRL ROOM) @
10kOhm
+20dB (INSERT) @ 10kOhm
More than 100mW (HEADPHONES° @33Ohm
T.H.D. <0.1% @ +14dB 20Hz~20kHz (MIX L/R, GROUP 1-2/3-4, AUX1,
AUX2/EFX SEND, CTRL ROOM) @10kOhm
Frequency response 20Hz~20kHz, +1/-2dB (MIX L/R, GROUP 1-2/3-4, AUX1, AUX2/EFX
SEND, CTRL ROOM) @10kOhm
Hum and Noise (average Rs=150Ohm) -127dB equivalent input noise
-95dB residual noise (MIX L/R, GROUP 1-2/3-4, AUX1, AUX2/EFX
SEND, CTRL ROOM)
-88dB (MIX L/R, GROUP 1-2/3-4, AUX1, AUX2/EFX SEND, CTRL
ROOM OUT) Master fader at nominal level and all channel assign
switches off.
Maximum Voltage Gain 74dB MIC IN TO Main L/R
74dB MIC IN TO GROUP 1-2/3-4
66dB MIC IN TO AUX1/AUX2 (PRE)
76dB MIC IN TO AUX2 (POST)
76dB MIC IN TO EFX
80dB MIC IN TO CONTROL ROOM L/R
52.2dB IN TO REC L/R
54dB LINE IN TO MIX L/R
54dB LINE IN TO GROUP 1-2/3-4
46dB LINE IN TO AUX1 / AUX2 (PRE)
56dB LINE IN TO AUX2 (POST)
60dB LINE IN TO CONTROL ROOM L/R
44dB STEREO IN TO MAIN L/R
44dB STEREO IN TO GROUP 1-2/3-4
16dB AUX RETURN IN TO MIX L/R
12dB AUX RETURN IN TO AUX1/AUX2
20dB TAPE IN TO MAIN L/R
Crosstalk (@ 1kHz) -70dB between input channels
-70dB between input/output channels
Gain Control (mono input channel) 44dB Variable (-50dB ~ -6dB) (-30dB ~ +14dB)
Gain Control 40dB Variable (-20dB ~ +20dB)
(combinated mono/stereo input channel)
Mono input channel Equalization HIGH: 12kHz shelving
MID: 100-8kHz peaking
LOW: 80Hz shelving
*Turnover/roll off frequencies: located 3dB below max. boost/cut
Stereo input channel Equalization HiGH: 12kHz shelving
HIGH MID: 3kHz peaking
LOW MID: 500Hz peaking
LOW: 80Hz shelving
*Turnover/roll off frequencies: located 3dB below max. boost/cut
Graphic Equalizer 7-band (63, 160, 400, 1K, 2.5K, 6.4K, 16KHZ)
LED Meters 2x 10 segment LED for MAIN L/R, GROUP1-2/3-4 or PFL
Internal Digital Effect 100 selectable presets
FOOT Switch control (ON/OFF)
Channel indicators Peak: an indicator for each channel turns on when the pré-channel
fader signal is 5dB below clipping
Phantom Power (balanced input) +48V DC
Weight 5,36 kg
Dimensions 436(W) x 90(H) x 420(D) mm
SYNQ 17/117
®
OPERATION MANUAL
SMP16.42
ENGLISH
Specifications
-INPUTS
- OUTPUTS
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
SYNQ 18/117
®
OPERATION MANUAL
SMP16.42