Q-Connect A4 STANDARD Mode D'emploi page 3

1 Inlet
2 Outlet
3 LED indicator (red when power on, green when ready)
4 Power button
5 Roller release button
6 Electric plug
7 Power socket
8. Temperature adjustor
GENERAL SAFEGUARDS
Failure to comply with any of the following safety precautions
may result in serious injury, fire or electrocution.
Keep out of the reach of children.
Unauthorized maintenance is not allowed.
Do not allow liquid to get into the machine.
Do not insert any foreign object or put your fingers or hand
inside. This machine is heat emitting, do not leave unattended
during operation.
Allow enough space behind the laminator to ensure free clear-
ance of the laminated object and prevent blockage.
OPERATING INSTRUCTIONS
HOT LAMINATING
1 Insert the electric plug (6) into the power socket (7).
2 Turn on the laminator by pressing the power button (4) which
will glow red when ON.
3 When the red light turns green, the laminator is ready for
operating
4 Adjust the temperature by turning the temperature adjustor
(8) so that the pointer is pointing to the corresponding tem-
perature/pouch setting.
5 Prepare the item to be laminated. Insert the item in between
the laminating pouch and push it to the sealed end of the
pouch. WE RECOMMEND TO USE Q-CONNECT LAMINATING
POUCHES.
6 Insert the sealed end of the pouch straight into the laminator
through the inlet (1). Once the pouch is engaged by the roller,
it will be rolled into the laminator automatically.
7 Remove the laminated item from the outlet (2).
8 After use, turn off the laminator by pressing the power button
(4).
COLD LAMINATING
1 Insert the electric plug (6) into the power socket (7).
2 Turn on the laminator by turning the Temperature control dial
(8) towards the COLD direction. Press down The Power button
(4).
3 The LED indicator (3) will turn green immediately.
4 Prepare the item to be laminated. Open the pouch and insert
the item in between the laminating pouch so that the part
with the protective paper is on top.
5 Peel off the first few centimeters of the protective paper and
insert the closed end of the pouch centrally into the laminator
through the inlet (1). Once the pouch is engaged by the roller,
carefully remove the protective paper as the pouch is rolled
into the laminator.
6 Remove the finished product from the outlet (2). Do not at-
tempt to pull the pouch out before the laminating process is
completed.
7 After use, turn off the laminator by pressing the power button
(4).
REMOVING JAMMED LAMINATING POUCHES
IIf the laminating pouch is jammed inside the laminator during
the laminating process, push the roller release lever (5) forward
and pull the jammed pouch out immediately.
After the jammed pouch is removed, release the roller release
button and continue with a fresh laminating pouch.
If the jammed pouch cannot be removed, turn off the laminator
and report to the dealer shop for assistance.
CLEANING THE LAMINATOR
After laminating several documents, adhesive
material from the pouch may accumulate inside the laminator.
Please clean the laminator regularly as follows:
1 Turn on the laminator until the LED indicator(3) turns green.
2 Fold a sheet of fresh copying paper once at the middle and
insert with the folded end first through the laminator. Repeat
the same procedure for 3 - 5 times.
CLEANING THE BODY
1 Unplug the laminator.
2 Wipe with a soft cloth and a general-purpose household
cleaner.
TECHNIC AL DATA
Max. Laminating width: 230mm.
Laminating speed: 300 mm/min.
Max. Laminating Thickness: 0,4mm.
Recommended Pouch Thickness: 80 - 125 mic per side.
Jammed paper release: roller release button.
2 rollers.
Pre-heat time: 3 - 5 min.
Voltage: 230 V / 50 Hz.
Consumption power: 300 W.
Current: 1,5 A.
Weight: 1,4 kg.
Dimensions: 358 x 148 x 66mm.
Body Material: ABS.
3
t