Ryobi CP-180M Manuel D'utilisation page 15

GB GB
F F D D
OPERATION
A pinch valve adaptor comes as part of the small inflatable
nozzle assembly that is attached to the end of the low
pressure air hose. The pinch valve adaptor is used for
items that have a smaller air opening or pinch valve.
n Insert pinch valve adaptor into pinch valve, insuring
that the tip of the adaptor is inserted past the inner
"flap" inside the valve. When inflating, ensure that the
tip is not blocked during inflation.
CAUTION:
Always leave low pressure hose free of
obstructions and with pinch valve adaptor off when
not in use. Overheating could occur low pressure
hose is blocked.
INFLATING WITH THE HIGH PRESSURE AIR HOSE
(FIG. 6-7)
The air chuck on the high pressure air hose can be used
without adaptors to inflate tires or with any application that
has a valve stem that fits the air chuck opening.
n Position air chuck clamp in the unlock position
perpendicular to the high pressure air hose.
n Place air chuck on valve stem.
n Push air chuck down so that the threaded section of
the valve stem is inside the air chuck.
n Clamp the end of the air chuck down onto the valve
stem by pressing air chuck clamp down until it stops
or is parallel with the high pressure air hose.
NOTE: When inflating items of 10 PSI., 0.65 BAR, 0.70
2
KG/CM or less, inflate in short bursts and check after
each burst by feel or with a calibrated measuring device
to determine accurate pressure.
INFLATING WITH THE HIGH PRESSURE AIR HOSE AND
ADAPTORS (FIG. 7-10)
The high pressure air hose can be used with the provided
adaptors to inflate a variety of items.
n Insert adaptor into air chuck and push air chuck clamp
down until it locks into place.
n To remove, lift air chuck clamp up and remove adaptor
from air chuck.
ADAPTORS (FIG. 7-9)
The supplied adaptors perform a variety of functions. The
Schrader valve removal tool can be used to remove valve
cores for quick deflation.
To use the sport ball needle:
n Insert sport ball needle into sports ball valve and inflate.
E E I I P P NL NL S S DK DK N N FIN FIN GR GR
English English
n Remove sport ball needle after inflation.
NOTE: Pressure required for most sports balls is too low
for accurate reading on gauge.
The Presta valve adaptor can be used for Presta valve
stems as described below. (See Figure 9) Before inflating
a tyre with a Presta valve, loosen the locking nut on the
valve stem to inflate. Once inflation is complete, tighten
the locking nut to seal the tyre valve.
To use the Presta valve adaptor:
n Loosen Presta valve locking nut.
n Thread Presta valve adaptor onto valve stem with
larger open end toward wheel.
n Position the air chuck clamp in the unlock position.
n Clamp the end of the air chuck down onto the Presta
valve adaptor by pressing air chuck clamp down until it
locks into place.
n After inflation, remove air chuck and tighten locking
nut.
QUICK SHUTOFF SWITCH (FIG. 11)
Depress the quick shutoff switch at any time to stop the
inflator.
DIGITAL GAUGE (FIG. 11)
NOTE: Digital gauge displays pressure of high
pressure hose only. Preset features apply to high pressure
applications only.
The digital gauge on the inflator is multifunctional. It
serves as a pressure gauge, monitors the amount of
pressure being applied to the item being inflated and can
change air pressure measurement units from PSI to BAR
to KG/CM
To turn the digital gauge ON, press the ON/RESET button
or depress the switch trigger.
NOTE: Make sure digital gauge is set at 0 before use. If
gauge reads "Err" or needs resetting, press and hold ON/
RESET button for 4-7 seconds.
NOTE: The digital gauge will automatically shut off when
not in use for 2 and a half minutes or more.
To use the pressure gauge feature:
n Turn digital gauge on by pressing ON/RESET button
or depressing and releasing switch trigger.
n Place air chuck over valve stem and lock in place.
Readout will appear on gauge.
NOTE: The pressure readout on the gauge while inflating
is a measurement of the fluctuating pressure between
the item and the high pressure hose. To get an accurate
reading, stop inflating and follow above instructions for
reading the air pressure.
11
RO RO
H H CZ CZ RUS RUS
2
.
HR HR
PL PL SLO SLO TR TR