Morphy Richards Supervac sleek pro Instructions page 10

VC734000MEE Rev2.qxp_Morphy Richards Instruction Book 17/12/2018 11:25 Page 10
Charging / storage mount fixing
Charge the product fully before first use.
1
The charging / storage mount (30) must be fixed to a suitable wall
using two 4mm (No. 8) counter-sunk screws.
The suggested minimum length of the screws is 38mm, to allow
for the 11mm of the screw as it passes through the charging /
storage mount.
The screws / plug must be suitable for the relevant wall type and
be capable of supporting a minimum of 10kg.
The position of the two holes for the fixing plugs should be as
shown in the diagram (see left).
WARNING: Always take care when drilling walls. Ensure the
wall is safe and sturdy and ensure there are no plumbing, gas
or electrical routes within the wall.
2
To charge, plug the mains adaptor (25) into the mains supply and
switch on, then plug the mains adaptor connector (24) into the
charging / storage mount charging inlet (32) on the underside of
the charging / storage mount.
After the charging / storage mount has been fixed to the wall with
the mains adaptor attached, simply seat the product into the
charging / storage mount for charging (see 'Set up and charging').
Multiple functionality
Your vacuum cleaner can easily be configured into three different
cleaning modes:
• Vacuum cleaner for floors and carpets.
• Handheld vacuum cleaner which can be carried with you whilst
cleaning.
• Extended reach vacuum cleaner for cleaning hard to reach places
such as high coving etc.
Set up and charging
Charge the product fully before first use.
4 Fit the battery (10). Hook the lower end of the battery into the
cleaner, then push the top of
the battery firmly until it locks into place.
The battery will not need to be removed again unless the product
reaches the end of its useful life.
Removal of battery or replacement:
If the battery needs to be removed again, slide the battery release
button (20) towards the handheld vacuum cleaner handle (1) and
pull from the top end of the battery to remove.
Only use battery number 734000-B for this product.
In extreme conditions, batteries may be subject to leakage. If
touched, wash skin with hot soapy warning. Do not try to use or
recharge the battery in this condition.
4 A Insert the mains adaptor connector (24) into the charging /
storage mount charging inlet (32). Seat the vacuum cleaner into
the charging / storage mount (30), ensuring the charging / storage
mount electrical connectors (29) align with the handheld vacuum
cleaner electrical connectors. Connect the mains adaptor (25) to
the mains supply.
10
3
4BAlternatively (provided the unit is in the charging / storage mount
(30)), insert the mains adaptor connector (24) into the handheld
vacuum cleaner charging inlet (2). The connector will only fit one
way. Connect the mains adaptor (25) to the mains supply.
After the adaptor is connected, the charge indicator (6) will
illuminate within a few seconds.
5 When the battery is empty and the product is put onto charge,
one bar of the charge indicator (6) will illuminate. As the battery
charges, the second bar of the charge indicator will start to flash
and then become steady, then the third bar will start to flash.
When the illumination of all three bars is steady, the product is
fully charged. A full charge may take 4 hours.
The three bars will stay illuminated for 5 minutes and then
extinguish to save power.
If all three bars are flashing, this indicates a fault, please see
'Maintenance - troubleshooting'.
When fully charged, the mains adaptor may be switched off and
unplugged. If unused, the batteries will remain charged for many
weeks so there is no need to keep constantly on charge.
Assembly in handstick mode
1 Push the neck of the motorised floor brush (23) into the extension
tube suction end (22) until it clicks into place, ensuring the
electrical connectors marry together.
2 Push the extension tube handheld connection end (19) into the
handheld vacuum cleaner suction inlet (18) until it clicks into
place.
Switching on and power settings
1 Press the On/Off button (7).
2 Pressing the On/Off button (7) will switch the product on at MAX.
A second press will change the power to TURBO, a third press will
change the power to MIN and a fourth press to OFF. The product
may also be switched off by pressing the On/Off button
continuously for 2 seconds.
When the product is on, one of the three power level indicator
lights (5) will illuminate to display which power setting has been
selected and the charge indicator (6) will also illuminate to show
the amount of battery charge remaining.
The MAX setting should be sufficient for the majority of cleaning
tasks. The TURBO setting will produce the best cleaning results,
but the battery charge will be used more quickly. Using on MIN
power will be sufficient for light cleaning and will extend the usage
time before the battery needs recharging.
NOTE: The motorised floor brush (23) will not rotate when the
MIN setting is chosen.
As the battery charge is diminished during use, the number of
illuminated bars on the charge indicator (6) will reduce. When the
last bar starts to flash, the battery charge is close to its minimum
limit. The product will automatically stop when the battery charge
reaches its minimum limit. The battery must then be
re-charged.
6
7 8