STEINEL HL Stick Mode D'emploi page 5

GB Translation of the original
operating instructions
Please familiarise yourself with these operating instructions
before using this product, because prolonged reliable and
trouble-free operation will only be ensured if it is handled
properly.
We hope your new hot air tool will give you lasting
satisfaction.
Safety precautions
Read and observe this information
before using the tool. Failure to
observe the operating instructions
may result in the tool becoming a
source of danger.
When using electric power tools,
observe the following basic safety
precautions to avoid electric shock
as well as the risk of injury and fire.
Used carelessly, the tool can start an
unintentional fire or injure persons.
Check the tool for any damage
(mains connection lead, housing
etc.) before putting it into operation
and do not use the tool if it is
damaged.
Do not leave the tool switched on
unattended.
Children should be supervised to
make sure they do not play with the
tool.
First time of use
A small quantity of smoke may de-
velop when the tool is used for the
first time. This smoke is caused by
binding agents released from the
heater's insulating film during the
first time of use.
About this document
Please read carefully and keep in a safe place.
- Under copyright. Reproduction either wholly or in part only
with our consent.
- Subject to change in the interest of technical progress.
To let the smoke escape quickly,
the tool should be set down on its
standing surface. The area you are
working in should be well ventilated
when using the tool for the first time.
Any smoke coming out of the tool is
not harmful!
Take the ambient
conditions into account.
Do not expose electric power tools
to rain. Do not use electric power
tools when they are damp or in a
damp or wet environment.
Exercise care when using the tool in
the proximity of flammable materials.
Do not direct the tool at one and the
same place for a prolonged period.
Do not use in the presence of an
explosive atmosphere. Heat may be
conducted to flammable materials
that are hidden from direct sight.
Protect yourself
from electric shock.
Avoid coming into contact with
grounded objects, such as pipes,
radiators, cookers or refrigerators.
Do not leave the tool unattended
while in operation.
- 8 -
Safety precautions
Store your tools
in a safe place.
After use, set the tool down on its
standing surface and let it cool be-
fore putting it away.
When not in use, tools must be
stored in a dry, locked room out of
children's reach.
This tool may be used by children
aged 8 or above and by persons
with reduced physical, sensory or
mental capabilities or lack of expe-
rience and knowledge if they are
supervised or have been given in-
structions on how to use the tool
safely and understand the hazards
involved.
Do not allow children to play with the
tool.
Children are not allowed to clean or
carry out maintenance work on the
tool without supervision.
Do not overload your tools.
Your work results and safety
will be enhanced if you operate
the tool within the specified output
range. Do not carry the tool by the
power cord. Do not unplug the tool
by pulling on the power cord. Pro-
tect the power cord from heat, oil
and sharp edges.
Proper use
The STEINEL HL Stick power tool is intended for shaping
plastic as well as for heating shrink tubing. It is also suitable
for soldering, de-soldering and undoing bonded joints.
Beware of toxic gases and
fire hazards.
Toxic gases may develop when
working on plastics, paints, varnish-
es or similar materials.
Beware of fire and ignition hazards.
For your own safety, only use ac-
cessories and attachments that are
specified in the operating instruc-
tions or recommended or specified
by the tool manufacturer.
Using attachments or accessories
other than those recommended in
the operating instructions or cata-
logue may result in personal
injury.
Repairs must only be carried
out by a qualified electrician.
This electric power tool complies
with the relevant safety regulations.
Repairs should only be performed by
a qualified electrician. Otherwise the
user may run the risk of accidents.
If this tool's main power cord is dam-
aged, it must be replaced by the
manufacturer or its customer service
department or a similarly qualified
person so as to avoid hazards.
Keep these safety precautions
with the tool.
The tool is not intended for use as a hot-air barbecue lighter,
as a hair-drier or for use in vehicles.
- 9 -