Field Of Application; Product Description; Particular Advantages; Technical Data - Trisk CureSaver 2 Manuel D'assemblage, D'utilisation Et Pièces De Rechange

English
2.

Field of application

The CureSaver 2 is used to accelerate the drying of
putty, filler, base and top coats. This applies to both
waterbased and solvent-based products. Its site of use
is the preparation area and finishing area. Within the
automotive industry and vehicle maintenance sectors,
it is used to dry small areas and cure materials before
polishing.
3.

Product description

The easily manoeuvrable CureSaver 2 is equipped with
a compact cassette. The cassette is equipped with 3 IR
lamps with aluminium reflectors and a ventilator. The
design, combined with a gas spring, makes cassette
adjustment simple. The IR lamps and reflectors are
protected against mechanical damage with a mesh. The
control unit enables flash off (50% heat applying) and
full bake (100% heat applying). The time can be
set individually for each status.

3.1 Particular advantages

3.1.1 Higher quality
Using the mobile dryer when you dry putty also
improves the quality of the top coat. The high surface
temperature and curing from the inside outwards drive
all solvents and other reaction products from the coated
material.
3.1.2 Short drying times
Putty 3 -5 min.
Filler 5 - 10 min.
Primer 8 - 12 min.
Water-base 4 - 6 min.
Base coat 4 - 8 min.
Top coat 8 - 12 min.
Clear varnish 8 - 12 min.
3.1.3 Low energy consumption
Electrical energy is used efficiently through short-wave
technology and aluminium coated reflectors. Surfaces
are subjected to targeted irradiation. The air is not
heated.
3.1.4 Good maneuverability
The units low weight and high reach makes the ma-
chines very competitive, versatile and easy to use.

3.2 Technical data

Electrical diagram, see chapter 11
For machine reach and dimensions, see last page.
420825 rev 2
Rated Voltage 220V - 240 V, 50/60Hz
Single Phase
Rated power 3 emitters, full power 3000 W
Heating elements 3 quartz, tungsten filament,
InfraRed emitters
Fuse* 16 A slow, type C (UK 13A) (NA 20 A)
Drying surfaces on 1,0 m x 0,9 m (width x height)
black sheet metal
Dimensions See last page
Weight 46 kg
Noice level Less than 70 dB (A)
Max ambient tempera-
ture during operation 40 o Celsius
Max ambient tempera-
ture during storage
and transportation 70 o Celsius
* The dryer must be supplied by recommended fuse.

4. Instruction to the owner

The owner of the mobile dryer must produce clear operat-
ing instructions, adapted to local site conditions, and
make these available to all users.
Mobile dryer users must adhere to these operating
instructions. This appliance is not intended for use by
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be super-
vised to ensure that they do not play with the appliance.
Dispose of spent items at the nearest environmental
protection facility for recycling.

5. Hazards

Fire and explosion
To reduce the risk of explosion, do not use in paint
spraybooths or within 5 m/16 feet of paint spraying
operations.
Do not store, prepare or use solvent-containing materi-
als within a 5 m/16 feet radius of the mobile dryer.
Flammable materials should not be placed close to a
drying device in use. If you have a distance less than
60 cm/2 feet to the object the temperature might raise
quickly and the risk for fi re increases. Never direct the
cassette towards highly combustible materials.
Electrical equipment
The mobile dryer is operated by highly dangerous electri-
cal voltage.
Accessing electrical equipment
Before accessing live parts, remove the main connec-
tor from the wall socket. Only professional electricians
may have direct access into the electrical equipment.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
WARNING!
Intensive heat radiation. Hands, face and other parts of
the body should be exposed as little as possible to the
heat radiation.
CureSaver 2
5