Precautions; Audio/Video Connections; Ntsc/Pal Switch - Rotel RDV-995 Manuel D'utilisation

RDV-995 DVD Player

Precautions

Please read this manual carefully. In addition
to basic installation and operating instructions,
it provides valuable information on various
system configurations as well as general in-
formation that will help you get the most from
your system. Please contact your authorized
Rotel dealer for answers to any questions you
might have. In addition, all of us at Rotel wel-
come your questions and comments.
Save the RDV-995 shipping carton and all en-
closed packing material for future use. Ship-
ping or moving the RDV-995 in anything other
than the original packing material may re-
sult in severe damage.
Be sure to keep the original sales receipt. It
is your best record of the date of purchase,
which you will need in the event warranty ser-
vice is ever required.
Figure 4: Rear Panel Connections
ANALOG
Apparatus Claims of
OUTPUT
U.S. Patent Nos.
4,631, 603, 4,577,216,
4,819,098, and
4,907,093 licensed
for limited viewing
uses only.
R L
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
1 1
Audio ANALOG OUTPUT jacks
Left and right channel analog audio outputs.
VIDEO OUT – COMPOSITE jack
Outputs a composite video signal.
VIDEO OUT – S VIDEO jack
Outputs an S-video signal.
COMPONENT VIDEO OUT jacks
Outputs component video signals.
Placement
Place the RDV-995 on a surface that is level,
dry and neither too hot nor too cold (between
5˚C and 35˚C, 41˚F and 95˚F). Do not place
the unit where it will be exposed to direct
sunlight. Avoid locations that are dusty. Do
not place the unit too close to the television
set. Do not place the RDV-995 where it will
be exposed to vibrations, such as near a sub-
woofer. To ensure proper ventilation observe
the minimum clearance specifications listed
in the safety information on page 2.

Audio/Video Connections

IMPORTANT NOTE
FOR 5.1 CHANNEL OPERATION:
Before using the RDV-995 in a 5.1 channel
system see the instructions on page 8 re-
garding the correct setting of the Digital
Audio Output preferences.
Manufactured under license from Dolby Laboratories. "Dolby" and the
double-D symbol are trademarks of Dolby Laboratories. Confidential
Unpublished Works. © 1992 - 1997 Dolby Laboratories, Inc. All rights
reserved.
VIDEO OUT
COMPOSITE S VIDEO
Y P P
B R
COMPONENT
12 13
14
NTSC/PAL Output Switch
Switches the video output signal between NTSC
and PAL formats.
DIGITAL OUT – OPTICAL jack
DIGITAL OUT – COAXIAL jack
Provide digital output signals. The output you use
(Optical or Coaxial) must be set in the "Prefer-
ence" on-screen menu.
6
DIGITAL OUT
OPTICAL COAXIAL
EXT REM
PAL NTSC
IN
Manufacured under license from Digital Theater Systems, Inc. US Pat. PRODUCT COMPLIES WITH DHHS RULES
No 5,451,942 and other world wide patents issued and pending. "DTS",
21 CFR SUBCHAPTER J IN EFFECT AT DATE
"DTS Digital Surround" are trademarks of Digital Theater Systems, Inc.
OF MANUFACTURE.
Copyright 1996 Digital Theater Systems, Inc. All Rights Reserved
15 16 17 18
NOTE: Do not plug in the power cable un-
til all audio/video signal connections are
complete. Do not change any audio/video
cable connections until the RDV-995 has
been unplugged from the power outlet.
Carefully read the instructions supplied with
the component you are going to connect to
the RDV-995 to be sure they are compatible.
If you have questions, contact your authorized
Rotel dealer.

NTSC/PAL Switch

Set the NTSC/PAL switch to the proper set-
ting for your TV. Television systems in North
America use the NTSC standard. Set the
NTSC/PAL switch before the RDV-995 is turned
on. It cannot be changed when the unit is on.
NOTE: Connect VIDEO OUT
unit directly to the video input of your TV.
Connecting VIDEO OUT to a TV via a VCR
may result in unacceptable video quality
because many discs are copy-protected.
DVD PLAYER
CLASS 1
MODEL NO. RDV-995
LASER PRODUCT
POWER CONSUMPTION : 20W
19
External Remote Input
("Ext Rem In")
This feature is useful when the unit is installed
in a cabinet and the front panel IR sensor is
blocked.
AC power cord receptacle
For the power cord connected to the wall out-
let.
of the
RP-385