Using The "Further Programme Preset" Function - Sony WIDE KP-44PS2 Mode D'emploi

Menu System

Using the "Further Programme Preset" function

With this feature you can:
a) Individually attenuate the strength of a channel signal in case of a strong local aerial signal (striped picture).
b) Individually adjust the volume level of each broadcast channel.
c) Normally the automatic fine tuning (AFT) is operating, however you can manually fine-tune the TV to obtain better
reception if the picture is distorted.
d) Preset the AV output for the programme positions of broadcast channels with scrambled signals (eg from a pay TV decoder). In
this way a connected VCR records the unscrambled signal.
TV
VIDEO
1 2 3
4 5 6
7 8 9
0
PROGR
MENU
RM 903
S
18
Menu System
1
Press the MENU button on the remote control to display the menu
on the screen.
2
Push the joystick $ to select the
the Set Up menu.
3
Push the joystick $ or 4 to select Manual Set Up then push to z
to enter.
4
Push the joystick $ or 4 to select Further Programme Preset,
then push z to enter.
5
Push the joystick $ or 4 to select the relevant programme number,
then push z repeatedly to select:
a) ATT (RF attenuator)
b) VOL (Volume Offset)
c) AFT (Automatic Fine Tuning) or
d) DECODER
The selected item changes colour.
6
a) ATT
Push the joystick $ to select On, then press the OK button.
Repeat steps 5 and 6 a) to attenuate other channels.
b) VOL
Push the joystick $ or 4 to adjust the volume level of the
channel over a range of -7 to +7, then press the OK button. Repeat
steps 5 and 6b) to adjust the volume level of the other
channels.
c) AFT
Push the joystick $ or 4 to fine tune the channel frequency over
a range of -15 to +15, then press the OK button. Repeat steps 5 and
6c) if you wish to fine tune other
d) DECODER
Push the joystick $ or 4 to select AV1 (for a decoder connected
to the Scart :1/ ) or AV2 (for a decoder connected to the Scart
:2/q 2 (SMARTLINK)), then press the OK button.
Repeat steps 5 and 6d) to select the AV1 or AV2 output for other
programme positions.
The picture from the decoder connected to the Scart connector
:1/ or :2/q 2 (SMARTLINK) on the back of the
set will appear on this programme number.
7
Press the MENU button to exit and return to the normal TV screen.
The set is now ready for use.
symbol, then push z to enter
broadcast
broadcast
broadcast channels.
Picture Adjustment
Picture Mode Personal
Contrast
Brightness
Colour
Sharpness
Reset
AI
On
Noise Detection
On
Digital Mode
DRC 50
Colour Tone
Normal
Select: Enter Menu:
Set Up
Auto Tuning Start
Programme Sorting
- - - - - - -
Select NexTView
AV Preset
Manual Set Up
Select: Start Auto Tuning
Set Up
Auto Tuning
Programme Sorting
- - - - - - -
Select NexTView
AV Preset
Manual Set Up
Select: Enter:
Manual Set Up
Language/Country
Manual Programme Preset
Further Programme Preset
RGB Set Up
- - - - - - -
Personal ID
Demo
Select: Enter:
Further Programme Preset
PROG ATT VOL AFT DECODER
1 Off 0 On Off
2 Off 0 On Off
3 Off 0 On Off
4
5
6
7
8
9
10
11
Select: Enter:
PROG ATT VOL AFT DECODER
1 Off
On
PROG ATT VOL AFT DECODER
1 On
- 5
PROG ATT VOL AFT DECODER
1 On -5
2
PROG ATT VOL AFT DECODER
1 On -5 2 Off
AV1
AV2