Package Contents; Safety Instructions - Renkforce 3897144 Mode D'emploi

G Operating instructions
13-Port USB3.0-Hub + 1x Charging Port
Item no. 1299048
Intended use
The product is designed for connection to a computer with a USB3.0 interface in order
to provide additional USB3.0 ports.
Furthermore, the USB3.0 hub offers a separate power outlet suitable for charging ap-
propriate devices such as a smartphone, tablet or iPad, etc.
Openings on the housing allow mounting of the USB3.0 hub e.g. below a work desk or
shelf or on a wall.
A standard power unit is used to supply the power.
Always observe the safety instructions and all other information included in these
operating instructions.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• USB3.0 Hub
• Power adapter
• Power cable
• USB cable
• Operating instructions
Explanation of symbols
The lightning symbol inside a triangle is a warning to inform you of potential
risks of personal injury, such as electrical shock.
This symbol points to specific risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety instructions
D amage due to not following these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Do not disassemble the
product.
• Any maintenance or repair work may be performed only by an expert.
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
b) Power adapter/power cable
• The design of the power adapter complies with safety class II. Only use a
standard mains socket as the voltage source for the power adapter.
• The mains socket into which the power cable is plugged must be easily
accessible.
• Use only the power adapter supplied to power the USB3.0 hub.
• Do not pull the power plug from the mains socket by pulling on the cable.
• If the power adapter or power cable is damaged, do not touch it; electric
shock carries a risk of danger to life!
First, switch off the mains voltage to the mains socket to which the power
adapter/power cable is connected (switch off at the corresponding circuit
breaker or remove the safety fuse and then switch off at the RCD protec-
tive switch, so that the socket is fully disconnected from the mains volt-
age).
Then you can remove the mains plug from the mains socket. Dispose of
the damaged power adaptor/power cable in an environment-friendly way;
do not use it any more. Replace it by a power supply unit / power cable of
the same design.
c) Operation
• This product is not a toy. Devices operated on mains voltage should not
be used by children. Therefore, be especially careful when children are
around.
Use the product where it is out of reach of children.
• The product is intended for use only in dry, enclosed indoor locations. No
part of the product should become damp or wet; never handle it if your
hands are wet!
With the power adapter/power cable there is also a risk of a potentially
fatal electric shock!
• When setting up the product, make sure that the cables are neither kinked
nor pinched.
• Do not apply force when connecting the USB plugs. A USB plug fits in the
USB socket only on one of its sides.
• Never use the product immediately after it has been taken from a cold
room into a warm one. The condensation that forms can ruin the product
under certain circumstances. Power supply unit / power cable also have
an associated risk for electric shock!
Allow the product to reach room temperature before connecting it to the
power supply and putting it to use. This may take several hours.
• Avoid the following adverse conditions at the location of installation and
during transport:
- Dampness or excessive humidity
- Extreme cold or heat, direct sunlight
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows
- Strong magnetic fields such as those found in the vicinity of machinery
or loudspeakers
Assembly
The USB3.0 hub can be mounted to a writing desk or wall with the openings at both
ends of the housing.
Use screws and, if necessary, screw anchors that are suitable for the sur-
face.
When mounting on a wall, make sure that no cables or wires are damaged
when drilling or screwing.
Connection and start-up
• Connect the circular low-voltage plug of the power adapter into the corresponding
socket of the USB3.0 hub.
• Connect the power adapter to a standard mains socket using the power cable en-
closed.
• Connect the USB3.0 hub via the enclosed USB cable to a free USB3.0 port on your
computer. The computer does not need to be switched off.
• Turn on the USB3.0 hub via the round pressure switch; the green LED Power lights
up.
Upon first use, the operating system will detect the new hardware and automatically
install the required drivers; they are already present in the operating system.
Please note:
When the USB3.0 hub is switched off, all USB ports and also the USB charg-
ing port are functionless.
• Connect your USB devices to the USB ports labelled "1" to "13" at the USB3.0 hub.
When a USB device has been detected, the corresponding blue LED on the USB3.0
hub lights up.
Of course, you can also connect and use USB2.0 and USB1.1 devices on the
USB3.0 hub.