Electrical Safety - DeWalt D27107 Traduction De La Notice D'instructions Originale

E N G L I S H
A8
42 Extension table (D271058)
A9
43 Sliding table (D271055)
Push sticks (DE3454) (not shown)
For use in all modes:
A10
44 Three way dust extraction kit (D271054)
A11
144 LED Worklight System
INTENDED USE
Your D WALT D27107 flip-over saw has been designed to operate as a
E
mitre saw or a saw bench to perform the four main sawing operations of
ripping, cross-cutting, bevelling and mitring easily, accurately and safely.
This unit is designed for use with a nominal blade diameter 305 mm carbide
tip blade for professional cutting wood, wood products and plastics.
DO NOT use under wet conditions or in presence of flammable liquids or
gases.
These flip over saws are professional power tools.
DO NOT let children come into contact with the tool. Supervision is required
when inexperienced operators use this tool.
WARNING! Do not use the machine for purposes other than
intended.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are supervised by a person
responsible for their safety. Children should never be left alone with this
product.
MITRE SAW MODE
In mitre saw mode, the sawing machine is used in vertical, mitre or bevel
position.
BENCH SAW MODE
Turned over on its central axis, the sawing machine is used to perform
the standard ripping operation and for sawing wide pieces by manually
feeding the workpiece into the blade.

Electrical Safety

The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your tool is double insulated in accordance with EN 61029;
therefore no earth wire is required.
In case of cord replacement the tool must only be repaired by an authorized
service agent or by qualified electrician.
Mains Plug Replacement
(U.K. & Ireland only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable
suitable for the power input of this tool (see Technical Data).The minimum
2
conductor size is 1.5 mm ; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
42
ASSEMBLY
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
Unpacking the machine and its parts
WARNING: To reduce the risk of injury, always seek assistance
when moving the machine.
• Remove the loose packaging material from the box.
• Lift the machine out of the box.
• Remove the parts box from the interior of the machine.
• Remove any remaining packing material from the machine.
Mounting the feet (fi g. A2, B, B1)
With the feet and legs mounted, alternatively the machine is suitable for
placement on a workbench. To ensure a safe operation, the machine must
be fastened to the workbench.
WARNING! Never operate this machine when it is not fastened
to the workbench. The feed force will make the saw unstable if
not fastened to the workbench.
• Turn the machine upside down.
• Place a foot (16) on each of the mounting locations (51) on the base.
• Slide a nut (52) into the slots (53) located above the mounting locations.
• Insert a bolt (54) fitted with a washer (55) into the feet.
• Tighten the bolts.
• Mount the legs as described below.
• Fold the legs as described below .
• Turn the machine straight up.
• Insert a bolt of 8 mm and 120 mm minimum length (49) into the feet on
each mounting location (fig. B1).
• Tighten the bolts.
Mounting the legs (fi g. C1 & C2)
With the legs mounted, the machine is suitable for stand-alone placement.
• Turn the machine upside down.
• Mount the legs as described below. Beware that the front legs and the
rear legs have different lengths. The rear legs are slightly longer than
the front legs. Make sure to mount the legs in the correct place.
• Turn the machine straight up. Make sure it is level; adjust the leg
clamping height if required.
Rear legs
• Present a leg (15) to each of the mounting points (56) located at the
lower edges on the inside of the base (fi g. C1).
• Pass a coach bolt (57) from the outside through the holes into the
frame and the legs.
• Place a bracket (58) and a lock knob (59) onto the bolts.
• Tighten the lock knobs.
Front legs
• Present a leg (15) to each of the mounting points (56) located at the
upper edges on the inside of the base (fi g. C2).
• Place a bracket (58) over the legs.
• Pass a coach bolt (57) from the inside through the holes into the
brackets, the legs and frame.
• Place a lock knob (59) onto the bolts.
• Tighten the lock knobs.
Folding the legs (fi g. C3, C4)
The legs can be folded into the base to make the machine suitable for use
on a workbench.
• Turn the machine upside down.