Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Running a wash cycle
NOTE: the first time you use the washer-dryer, add
GB
detergent and run an empty 90°C cotton wash cycle
without the pre-wash phase.
1. SWITCH THE MACHINE ON. Press the
All the indicator lights will illuminate for 1 second
and the text OK will appear on the display; the
indicator light corresponding to the
then remain lit in a constant manner and the
START/PAUSE indicator light will flash.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated by the display and
in the programme table on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
"Description of the machine".
For advice as to the type of detergent to use for
each cycle, press the
4. CLOSE THE PORTHOLE DOOR.
5. SELECT THE PROGRAMME. Turn the
PROGRAMME KNOB left or right, until the required
programme has been selected; the name of the
programme will appear on the display. A tempera-
ture and spin speed is set for each programme;
these may be adjusted. The recommended drum
load level and the cycle duration will also appear on
the display.
6. PERSONALISE THE WASH CYCLE. Use the
relevant buttons on the control panel:
Modify the temperature and/or the spin
speed. The machine automatically selects the
temperature and the maximum spin speed for the
programme set and these values may not be
increased. By pressing the
rature can be progressively reduced or even set to
cold wash “OFF”. By pressing the
spin speed can be progressively reduced or even
eliminated altogether “OFF”. If the buttons are
pressed again the maximum values are restored.
Exception: if the COTTON WHITES programme is
selected, the temperature can be increased up to
a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option has been activated, the
on the display. To remove the delayed start option,
press the button until the display shows the text
OFF; the
symbol will disappear.
20
button.
button will
button.
button, the tempe-
button, the
symbol appears
Modifying the cycle settings.
• Press the button to activate the option; the name
of the option will then appear on the display and
the corresponding indicator light will illuminate.
• Press the button again to deactivate the option;
the name of the option will then appear on the
display followed by the text OFF, and the
corresponding indicator light will switch off.
If the selected option is not compatible with the
set programme, the indicator light will flash and the
option will not be activated.
If the selected option is not compatible with
another option that has been selected previously,
the indicator light corresponding to the first option
selected will flash and only the second option will be
activated; the indicator light corresponding to the
active option will remain lit in a constant manner.
The options may affect the recommended load
value and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light
remains lit in a fixed manner and the porthole door
locks (the DOOR LOCKED indicator light
illuminates). During the wash cycle, the display will
show which stage is currently in progress and the
icon corresponding to each stage will illuminate. To
change a programme while a cycle is in progress,
pause the washer-dryer by pressing the START/
PAUSE button; then select the desired cycle and
press the START/PAUSE button again.
To open the door while a cycle is in progress press
the START/PAUSE button; if the DOOR LOCK
indicator light switches off it is possible to open the
door. Press the START/PAUSE button again to
resatrt the programme from the point at which it
was interrupted.
8. PROGRAMME END. The text END lights up to
indicate that the programme has ended. The
porthole door may be opened immediately. If the
START/PAUSE button flashes, press the button to
end the cycle. open the door, unload the laundry
and switch off the machine.
If you wish to cancel a cycle that has already
begun, press and hold the
stopped and the machine will switch off.
button. The cycle will be
Publicité
Table des Matières
